#ifndef INTERFACE_H #define INTERFACE_H #include struct T_emp { // Fixdata from EMP: uint8_t shaft; // = changer level uint16_t countryCode; uint8_t scale; uint8_t decimals; uint8_t coinValues[16]; uint16_t routing; // Master specs: uint8_t gotSetup; // 1: got specifications from master 0: no specs uint16_t coinAccept; // bit 0 = coin1 bit H=accept uint8_t tokenChannel; uint16_t denomination[16]; // dynamic: uint8_t state; // step counter of EMP (electronic coin checker) FSM (finite state machine): // 0=start command // 1=powered, do emp ini, send reset // 2=delay // 3=wait for response, requesting status after response // 4,5 through, startup // 6: wait for status // 7: through, startup // 8: IDLE state. EMP is up and ready, polling is running // 9: polling on, payment not yet on // 10: payment, check coins // 11: through // 12: wait 1s for last coin // 90: stop all, 1s delay // 99: off, all stopped uint8_t pollingRunning; uint8_t paymentRunning; }; struct Trtc_DateTime { uint8_t rtc_hour; uint8_t rtc_min; uint8_t rtc_sec; uint8_t rtc_dayOfMonth; uint8_t rtc_month; uint8_t rtc_year; uint8_t rtc_dayOfWeek; }; struct Tprn_hw_state { // hardware (IO's) bool powerRdBk; // prn pwr is on bool rsSwOk; // serial switch (printer or modem) is set to printer bool rsDrvOk; // RS232 converter for PTU, Printer and Modem in on bool ReadyLine; // HW signal from printer showing ready bool inIdle; // powered and free from errors bool paperNearEnd; // paper roll runs out bool noPaper; bool ErrorTemp; bool HeadOpen; bool cutterJam; bool noResponse; // printer is not connected, cable broken, wrong baudrate bool badResponse; }; struct Tprn_currentSettings { uint8_t currFont; uint8_t currSize; uint8_t currHeigth; uint8_t currWidth; bool nowBold; bool nowInvers; bool nowUnderlined; uint8_t currDensity; uint8_t currSpeed; bool nowAligned; }; // obsolete struct T_dynDat { uint8_t licensePlate[8]; uint8_t vendingPrice[8]; uint8_t parkingEnd[8]; uint8_t currentTime[8]; uint8_t currentDate[8]; uint8_t dynDat5[8]; uint8_t dynDat6[8]; uint8_t dynDat7[8]; }; struct T_vaultRecord { // Kassenbeleg (Abrechnungsdatensatz = Kassenwechsel-Datensatz) char startbuffer[4]; // Psa> // never move or change this 1st entry uint16_t AccountingNumber; uint16_t CUNU; uint16_t MANU; uint16_t resint1; //uint16_t resint2; char label1buffer[4]; // tim> uint8_t year; uint8_t month; uint8_t dom; uint8_t hour; uint8_t min; uint8_t sec; uint8_t DoW; uint8_t reschar3; char label2buffer[4]; // abs> uint32_t AbsIncome1; uint32_t AbsReserve; uint32_t AbsNrOfCuts; //16 char label3buffer[4]; // mw > // Verkauf, Tür zu: uint32_t VKcoinsInserted[16]; // nur für Wechsler, soviel wurde eingeworfen uint32_t VKcoinsReturned[6]; // nur für Wechsler, Anzahl Münzen pro Typ, soviel wurde zurückgegeben //88 // Service, Tür offen: uint16_t ServCoinsInserted[16]; // nur für Wechsler, soviel wurde eingeworfen uint16_t ServCoinsReturned[6]; // nur für Wechsler, Anzahl Münzen pro Typ, soviel wurde zurückgegeben uint16_t resint3; uint16_t resint4; uint16_t currentTubeContent[6]; // nur für Wechsler, aktueller Füllstand uint16_t resint5; uint16_t resint6; // 56 char label4buffer[4]; // box> uint16_t coinsInVault[16]; uint16_t billsInStacker[8]; // 48 char label5buffer[4]; // val> // actually constant unless exchange rate is changed uint16_t coinDenomination[16]; // 5..50000 (z.B. 2? sind in Ungarn 760Ft) uint16_t billDenom[8]; uint16_t tubeDenom[6]; uint16_t exchangeRate; uint16_t resint9; // 64 char endofblock[4]; // end> // 316 byte Block im Speicher }; struct T_moduleCondition { // store conditon of all system components, hold in RAM // 0 means unknown, not yet tested/used // 1 means OK // 50..99 = HINT / Notification // 100..150 = WARNING // 200..250 = ERROR uint8_t ram; uint8_t intEe; uint8_t extEe; uint8_t rtc; // 1: time/date OK 100: time not plausible 200: hardware error uint8_t boardHw; uint8_t printer; uint8_t modem; uint8_t signal; // 1...99 uint8_t regist; // 100:not 1:reg 2:ping OK 3:gotTime uint8_t mdbBus; uint8_t coinChecker; // EMP, OMP or mei-cashflow uint8_t coinEscrow; uint8_t mifareReader; uint8_t creditTerm; uint8_t coinReject; uint8_t coinSafe; uint8_t billSafe; uint8_t voltage; // 1:11..14V uint8_t temper; uint8_t poweronTest; uint8_t doorState; // 1: alles zu 200: t?r offen + bit1(S) +bit2(CB) + bit3(CB) uint8_t doorWasOpened; // 1: all doors are closed 200: any door was just opened uint8_t changer; // can only be tested by usage uint8_t coinBlocker; // can only be tested by usage uint8_t billReader; // can only be tested by usage uint8_t ResetReason; uint8_t allModulesChecked; uint8_t alarmState; uint8_t res11; uint8_t res12; uint8_t res13; }; struct T_dynamicCondition { char allDoorsDebounced; char openedAuthorized; uint8_t CBinDebounced; // 0:fehlt 1:drin char upperDoor; // 99: undefined 0:closed 1:open char middleDoor; // 99: undefined 0:closed 1:open char lowerDoor; // 99: undefined 0:closed 1:open char reserve; char billBox; char modeAbrech; char onAlarm; // 0:alarm aus 1:alarm 2:alarm mit Sirene 3: Sirenentest char nowCardTest; char nowPayment; // not used, always 0 char lastMifCardType; uint8_t lastSDoorState; uint8_t lastVDoorState; uint8_t lastCBstate; char paymentInProgress; // 0: stopped by timeout // 1: running 2: wait4lastCoin // 3: payment stopped manually, coins in Escrow // 4: payment stopped autom, amount collected, coins in Escrow // 5: payment stopped, escrow full, coins in Escrow // 6: coins encashed 7:coins returned // 8: CoinChecker or MDB on Error char res1; uint16_t U_Batt; uint16_t Temperatur; uint16_t nrCoinsInBox; uint32_t amountInBox; uint32_t totalTransVolume; uint32_t totalNrOfVends; char jsonValid_config; char jsonValid_device; char jsonValid_cash; char jsonValid_print; char jsonValid_serial; char jsonValid_time; char lastFileType; // 44 uint8_t MifCardHolder[8]; uint8_t resultOfLastTemplPrint; // 0: unknown or printing in progress // 1: OK, doc was printed 2: error, doc was not printed uint8_t lastPrinterStatus; // 0: printer OK // bit0: near paper end bit1: no paper // bit2: temperature error bit3: error head open // bit4: paper jam in cutter // bit6: no response bit7: serial rec. error // bit5: printer not ready uint8_t startupTestIsRunning; //54 }; struct T_extTime { uint8_t Hours; uint8_t Min; uint8_t Sec; uint8_t Year; uint8_t Month; uint8_t Day; uint8_t DOW; uint8_t res1; uint16_t MinOfDay; uint16_t res2; uint32_t SecOfDay; uint8_t isLeapYear; uint8_t nxtLeapYear; uint8_t lastLeapYear; uint8_t hoursOfThisWeek; uint16_t minutesOfThisWeek; uint16_t hoursOfThisMonth; uint16_t daysOfThisYear; uint16_t GetHoursOfYear; uint16_t res3; uint32_t GetMinutesOfYear; uint8_t getWakeIntvSec; uint8_t res4; uint16_t res5; uint32_t MinutesOfMillenium; }; typedef uint8_t UCHAR; typedef uint16_t UINT; struct T_devices { // set by master, used(1) or notused (0) or type 2....20 UCHAR kindOfPrinter; // 0:off 1:Gebe UCHAR kindOfCoinChecker; // 0: without 1=EMP820 2=EMP900 3=currenza c² (MW) UCHAR kindOfMifareReader; // by now only stronglink SL025 =1 UCHAR suppressSleepMode; // 0:sleep allowed 1: no sleep UCHAR kindOfModem; // 0:off 1:Sunlink UCHAR kindOfCreditcard; // 0:off 1:Feig NFC UCHAR CoinEscrow; UCHAR CoinRejectUnit; UCHAR CoinShutter; UCHAR BillAcceptor; UCHAR usevaultLock; UCHAR autoAlarm; // 1: switch on siren for 1min in doors opened unauthorized UCHAR autoOpen; // 1: open door covers after valid ATBcard UCHAR printAccReceipt; // 0/1 UCHAR printDoorReceipt; UCHAR printTokenTicket; UINT VaultFullWarnLevel; UINT VaultFullErrorLevel; }; class hwinf { public: virtual ~hwinf() {} // $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ // Use serial interface and protocol stack in Cashagent-Library // Sending Output data to DeviceController DC2b // Sending input requests to DC2 (single or auto-batch) // Getting input data as receiver payload // Furthermore the Cashagent-Library answers with status strings about sending and reading result // $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ virtual bool dc_openSerial(int BaudNr, QString BaudStr, QString ComName, uint8_t connect) const =0; // Command: open serial interface // BaudNr: 0:1200 1:9600 2:19200 3:38400 4:57600 5:115200 // BaudStr: for exapmle "19200" // ComName: for example "COM48" // connect: 0, 1 virtual void dc_closeSerial(void) const =0; // Command: close serial interface in order to save power while power down // or if another port must be used virtual bool dc_isPortOpen(void) const =0; // returns true if port open (don't send unless open. Sending to closed port will crash program) virtual uint8_t test_serialState(void) const =0; // test on-board signals for the serials // serial drv on/off, Serial mux1, Serial mux2 virtual bool test_serialIsOn(void) const =0; virtual void dc_autoRequest(bool on) const =0; // on = true: select that all READ-Requests are sent automatically // on = false: select that all READ-Requests are sent manually one by one // Every input information from DC2 must be requested // ( digital and analog sensors, get time/date, get status information ) virtual uint8_t dc_isRequestDone(void) const =0; // retval: 0: request is still in progress // 1: answer from DC2 was OK // 2: wrong answer from DC2 virtual uint16_t dc_getCompletePayLoad(uint16_t plBufSiz, uint8_t *payLoad) const =0; // get data back in "payLoad", max 64 byte, can be used for diagnosis // retval = nr of bytes received. If host buffer too small then // only plBufSiz bytes are copied to "payLoad" // plBufSiz­z=size of host buffer virtual void dc_requTestResponse() const =0; // tell DC2 to send a test-string, useful to see if cable and baudrate is OK virtual bool dc_readAnswTestResponse() const =0; // retval: true: test was successful, got right response virtual uint8_t getRawRecLength(void) const =0; // only needed if protocol stack in Cashagent-Library is bypassed virtual uint8_t getRawReceivedData(uint8_t *receivedData) const =0; // only needed if protocol stack in Cashagent-Library is bypassed virtual QString dc_getSerialState(void) const =0; // get result of opening-command like "ttyS0 opened with 115200 8N1! // or error messages like "comport not available..." // was saved by last opening event, can be passed for 100ms virtual void dc_clrSerialStateText(void) const =0; // clear above text to avoid multiple repetive displaying virtual QString dc_getTxt4HsStateLine(void) const =0; // return string with status of handshakes virtual void dc_clrTxt4HsStateLine(void) const =0; // clear above text to avoid multiple repetive displaying virtual QString dc_getTxt4masterStateLine(void) const =0; // returns string telling if the received packet is valid and complies protocol // if OK: "slave response OK" in case of error: "wrong length received", "wrong start sign received", // "received datalen to big", "wrong data len received", "wrong crc received" virtual void dc_clrTxt4masterStateLine(void) const =0; // clear above text to avoid multiple repetive displaying virtual QString dc_getTxt4resultStateLine(void) const =0; // returns string telling response of DC. First question: did DC get a correct request telegram? // and if: 2nd question did DC perform the contained output and input commands // if OK: "Slave OUT and IN Result: 0 0" // in case of error: "slave got wrong start sign" ..length" ...crc" ... address" // slave does not perform and command! // 2nd) received telegram was OK, DC tried to perform the master commands. result // result of writing data (e.g switching leds and motors, sending stuff to printer...) // OUT = 0: OK 1: unknown command 2: operation not possible // result of reading data (e.g. switches, voltages, accepted coins, printer status....) // IN = 0: OK 1: unknown command 2: could not read due to hardware error 3: could not read because device is off virtual void dc_clrTxt4resultStateLine(void) const =0; // clear above text to avoid multiple repetive displaying virtual QString dc_getdataStateLine(void) const =0; // check if recveied input data are ok/valid // OK-string : "valid INdata...." with protocol details // not OK: string empty virtual void dc_clrTxt4dataStateLine(void) const =0; // clear above text to avoid multiple repetive displaying virtual QString dc_getdatifLine(void) const =0; // returns string with result of function dc_requTestResponse() // "correct" or "false" virtual void dc_clrTxt4datifLine(void) const =0; // clear above text to avoid multiple repetive displaying virtual QString dc_getTxt4RsDiagWin(void) const =0; // returns string to be displayed in "serial traffic" window // details about sent and received protocol virtual void dc_clrTxt4RsDiagWin(void) const =0; // clear above text to avoid multiple repetive displaying virtual QString dc_get2ndTxt4RsDiagWin(void) const =0; // returns string to be displayed in "serial traffic" window // details about sent and received protocol virtual void dc_clr2ndTxt4RsDiagWin(void) const =0; // clear above text to avoid multiple repetive displaying // 28 functions // $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ // DC2b internal data // $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ virtual QString dc_getSerialParams(void) const =0; // get DC2 serial settings (not very meaningful as they will not come if different from master settings) virtual QString dc_getHWversion(void) const =0; // get DC2 hardware version virtual QString dc_getSWversion(void) const =0; // get DC2 software version virtual QString dc_getState(void) const =0; // get DC2 status (every OK or any error/warning? ) // UID - unique number, different in every DC virtual void dc_getUID8byte(uint8_t *buf8byteUid) const =0; // get 8 single bytes in buffer virtual QString dc_getUIDstr() const =0; // get as string virtual uint64_t dc_getUIDnumber(void) const =0; // get UID as one long number // Analog values: virtual uint32_t dc_getTemperature(void) const =0; // in Sax-Format 0...400 (0=-50,0°C 100=0,0°C 141=20,5°C 400=150,0°C) virtual QString dc_getTemperaturStr(void) const =0; // as string like "-12,5°C" virtual uint32_t dc_getVoltage(void) const =0; // as value in mV, 0...65,535V virtual QString dc_getVoltagStr(void) const =0; // as string in mV virtual bool dc_mainFuseIsOk(void) const=0; // true if 12V fuse is OK // false: fuse blown, DC will continue working but no 12V device can be used! virtual void dc_setWakeFrequency(uint8_t period) const =0; // RTC wakes DC2 (and PTU) by hardware signal every 32seconds // change wake signal period to 1...64s virtual void dc_OrderToReset(void) const =0; // want DC2 to reset (in order to start Bootloader) // all read-requests can be sent manually by the following functions // or automatically in background by: void hwapi::dc_autoRequest(bool on) // in other words: // if automatic-reading is on, then there's no need to send any of these commands, // but it's allowed to send them in order to speed up the refreshing of the inputs virtual void request_DC2serialConfig() const =0; // read-request can be sent manually by this function, not needed if auto-request is on virtual void request_DC2_HWversion() const =0; // read-request can be sent manually by this function, not needed if auto-request is on virtual void request_DC2_SWversion() const =0; // read-request can be sent manually by this function, not needed if auto-request is on virtual void request_DC2_condition() const =0; // read-request can be sent manually by this function, not needed if auto-request is on virtual void request_DC2_UID() const =0; // read-request can be sent manually by this function, not needed if auto-request is on virtual void request_DC2_analogues() const =0; // read-request can be sent manually by this function, not needed if auto-request is on virtual void request_DC2_digitalInputs() const =0; // read-request can be sent manually by this function, not needed if auto-request is on virtual void request_DC2_digitalOutputs() const =0; // read-request can be sent manually by this function, not needed if auto-request is on // 22 // $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ // using DC2 Bootloader // $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ virtual void bl_sendDataDirectly(uint8_t length, uint8_t *buf) const =0; // send without protocol frame, needed for the DC bootloader virtual void bl_iniChain(void) const =0; virtual bool bl_importBinFile(QByteArray readBinFile, uint32_t fileSize, char withDispl) const =0; virtual uint8_t bl_activatBootloader(uint8_t *sendData) const =0; virtual uint8_t bl_startChain(void) const =0; virtual uint8_t bl_readBLversion(uint8_t *sendData) const =0; // minimum size of sendData-buffer: 5byte retval: length virtual uint8_t bl_readFWversion(uint8_t *sendData) const =0; // minimum size of sendData-buffer: 5byte retval: length virtual uint8_t bl_prepareDC_BLcmd(uint8_t Cmd, uint8_t SendDataLength, uint8_t *sendData, uint8_t *outBuf) const =0; // make BL protocol, retval = outbuf length (5...133) // bring data in correct form: start always with 0x02 finish with 0x03 and append checksum // 0x02 Cmd < ...sendData ..> CRC CRC 0x03 // Data length = 0...64 // special conversion: if data contain 2 or 3 (STX, ETX) then write two bytes: 0x1B (=ESC) and data|0x80 // so maxlength = 5 + 2 x 64 (if all data are 2 or 3) without 2,3: maxlength = 5 + 64 virtual uint8_t bl_exitBL(uint8_t *sendData) const =0; // minimum size of sendData-buffer: 5byte retval: length // 9 // $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ // get Time and Date from DC2b (contains a buffered real time clock) valid for about three days without power // $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ virtual uint8_t rtc_getDateTime(struct Trtc_DateTime *rtc_DateTime) const =0; virtual uint8_t rtc_setDateTime(void) const =0; // synch DC2 with PC or PTU system time and date virtual void rtc_getTime(uint8_t *hh, uint8_t *mm, uint8_t *ss) const =0; // get time directly virtual void rtc_getDate(uint8_t *yy, uint8_t *mm, uint8_t *dd) const =0; // get date directly virtual uint8_t rtc_getToday(uint8_t *dow, uint16_t *minOfToday, uint32_t *secOfToday) const =0; // dow=day of week, 1=monday...7 // minOfToday: 0=midnight...1439= 23:59 // secOfToday: 0=midnight...86399= 23:59:59 virtual bool rtc_isLeapYear(uint8_t *lastLeapYear, uint8_t *NextLeapYear) const =0; // retval true: this year is leap year virtual bool rtc_isLeapYear() const =0; virtual void rtc_getWeek(uint8_t *DayOfWeek, uint8_t *HoursOfWeek, uint16_t *MinutesOfWeek) const =0; // DayOfWeek: 1=monday...7 // HoursOfWeek: 0=Monday 0:00 o'clock...167=Sunday 23:00 // MinutesOfWeek: 0=Monday 0:00 o'clock...10079=Sunday 23:59 virtual void rtc_getMonth(uint8_t *DayOfMonth, uint16_t *HoursOfMonth, uint16_t *MinutesOfMonth) const =0; // DayOfMonth: 1...31 // HoursOfMonth: 0 = 0:00o'clock of 1.day in month up to 743 // MinutesOfMonth:0 = 0:00o'clock of 1.day in month up to 44639 virtual void rtc_getYear(uint16_t *DayOfYear, uint16_t *HoursOfYear, uint32_t *MinutesOfYear) const =0; // DayOfYear: 1...366 1= 1.Jan of this current year // HoursOfYear: 0=1.Jan 0:00o'clock ...8783=31.12 23 o'clock // MinutesOfYear: 0=1.Jan 0:00o'clock ...527039=31.12 23:59 o'clock virtual QString rtc_getTimStr(void) const =0; virtual QString rtc_getDatStr(void) const =0; virtual QString rtc_getTimDatStr(void) const =0; virtual void request_DC2_TimeAndDate() const =0; // read-request can be sent manually by this function, not needed if auto-request is on // 14 // $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ // PTU, Master // $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ virtual void ptu_switchWake(bool WAKEACTIVE) const =0; virtual bool ptu_WakeINisActive(void) const =0; virtual bool ptu_WakeOutIsOn(void) const =0; virtual void sendDeviceSettings(uint8_t kindOfPrinter, uint8_t kindOfCoinChecker, uint8_t kindOfMifareReader, uint8_t suppressSleep, uint8_t kindOfModem, uint8_t kindOfCredit ) const =0; // enable hardware in device controller: // kindOfPrinter: 0:off 1: GPT4672 (only this one implemented) // kindOfCoinChecker: 0:off 1:EMP820 2:EMP900 3: C²_changer // kindOfMifareReader: 0:off 1: SL025 (only this one implemented) // suppressSleep: 0:sleep allowed 1: sleep surpressed for special reason // kindOfModem: 0:off 1: ATB_Sunlink_LTE (not yet implemented) // kindOfCredit: 0:off 1: cVendTopp 2:cVendPin (not yet implemented) virtual void request_ReadbackDeviceSettings() const =0; virtual void readback_DeviceSettings(uint8_t *length, uint8_t *data) const =0; /* buf66[0]=devPara.kindOfPrinter; buf66[1]=devPara.kindOfCoinChecker; buf66[2]=devPara.kindOfMifareReader; buf66[3]=devPara.suppressSleepMode; buf66[4]=devPara.kindOfModem; buf66[5]=devPara.kindOfCreditcard; buf66[6]=devPara.CoinEscrow; buf66[7]=devPara.CoinRejectUnit; buf66[8]=devPara.CoinShutter; buf66[9]=devPara.BillAcceptor; buf66[10]=devPara.usevaultLock; buf66[11]=devPara.autoAlarm; buf66[12]=devPara.autoOpen; buf66[13]=devPara.printAccReceipt; buf66[14]=devPara.printDoorReceipt; buf66[15]=devPara.printTokenTicket; uitmp=devPara.VaultFullWarnLevel; buf66[16]=swl_getOneByteFromUint(uitmp, GETLOWBYT); buf66[17]=swl_getOneByteFromUint(uitmp, GETHIGHBYT); uitmp=devPara.VaultFullErrorLevel; buf66[18]=swl_getOneByteFromUint(uitmp, GETLOWBYT); buf66[19]=swl_getOneByteFromUint(uitmp, GETHIGHBYT); */ virtual void sendMachineID(uint16_t customerNr, uint16_t machineNr, uint16_t borough, uint16_t zone, uint16_t alias, char *location) const =0; virtual void request_ReadbackMachineID() const =0; virtual void readback_machineIDdata(uint8_t *length, uint8_t *data) const =0; // state 5.5.21: byte[0,1]=customer number byte[2,3]=machine number // byte[4,5]=borough byte[6,7]=zone byte[8,9]=alias name // byte[10...41]=location // 12.4.23TS still the same // $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ // Printer // $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ virtual void prn_switchPower(bool on) const =0; virtual bool prn_isPrinterPowerOn(void) const =0; virtual uint8_t prn_PrnFuseIsOk(void) const=0; //retval: 0: fuse blown 1: fuse OK 2:unknown as printer power is off virtual bool prn_readyINisActive(void) const =0; virtual uint8_t cash_getLowPaperSensor(void) const=0; // 0: Sensor sees paper 1: no paper 99: off // the following device state requests are deployed only if device is powered up: virtual void request_PrinterHwState() const =0; virtual void request_PrinterCurrentFonts() const =0; virtual void request_PrinterStateComplete() const =0; virtual bool test_serialMux1isSetToPrinter(void) const =0; // read printer condition and settings virtual uint8_t prn_getHwState(struct Tprn_hw_state *prn_hw_state) const =0; // retval: status byte // byte 0 = 0: prnter OK, >0: error // bit0: paper low 1: no paper 2: temperature error // 3: head open 4: paper jam in cutter // 6: no response 7: bad response from printer // and return struct "Tprn_hw_state" virtual bool prn_isUpAndReady(void) const =0; // true: printer is powered, serial is ok, no error, printer is connected and resonding virtual void prn_getCurrentFontSetting(struct Tprn_currentSettings *prn_fonts) const =0; // send Commands to printer: virtual void prn_sendText(QByteArray *buf) const =0; // up to 1280 bytes virtual void prn_sendPrnSysCmd(uint8_t para1, uint8_t para2, uint32_t para3) const =0; // send three byte through to printer, see printers manual virtual void prn_sendPrnEscCmd(uint8_t para1, uint8_t para2, uint8_t para3, uint8_t para4) const =0; // send four byte through to printer, see printers manual virtual void prn_sendPrnSetup(uint16_t paperSpeed, uint8_t density, uint8_t alignment, uint8_t orientation) const =0; // send 5 byte: byte 0,1: speed 5...250 mm/s // byte2: density 0....(25)....50 // byte3: alignment 'l', 'c', 'r' = left, center, right // byte4: orientation 0, 90, 180 = 0°, 90°, 180° rotation (by now not supported!) // not batched! don't use twice within 100ms virtual void prn_movePaper(uint8_t wayInMm, uint8_t direction) const =0; //direction: 1=forward 2=backward // virtual void prn_setFonts(uint8_t font, uint8_t size, uint8_t width, uint8_t height) const =0; // font = kind of font 5...11 (0..22) // size = 6...20, 9..9: too tiny 10: small ...12 = normal size ...20=huge // width: 0...4 0=1x 1=2x 2=4x (huge!) 3=8x 4=16x (3,4 make no sense) // heigth: 0...7 = 1x...8x only 0,1,2,(3) make sense virtual void prn_setLetters(uint8_t bold, uint8_t invers, uint8_t underlined) const =0; // bold: 0/1 // invers: 0/1 // underlined: 0/1 virtual void prn_cut(uint8_t kindof) const =0; // kindof: 1=full cut 2=partial cut 3=eject (5xLF + full cut) virtual void prn_newLine(uint8_t nrOfLines) const =0; virtual void prn_printCompleteFontTable(void) const =0; virtual void prn_printBarcode(uint8_t kindOf, uint8_t withText, uint8_t offset, uint8_t rotation, uint8_t dataLeng, uint8_t *data) const =0; // kind of barcode: 0=Code39 1=Code128 2=EAN13 3= 2/5interleaved 4=UPC-A 5=EAN8 // withText: print readable text below // offset: move by pixel from left border // rotation // dataLeng in byte virtual void prn_sendQRdata(QByteArray *buf) const =0; // maximal 150 alphanummeric bytes virtual void prn_printQRcode(void) const =0; // QRcode may have 1...150 alphanummeric data, must be transfered in advance virtual void prn_printLogo(uint8_t nrOfLogo, uint8_t offset ) const =0; // nrOfLogo: 1..4 in flash 5...8 in Ram // offset: in mm form left border // ......................................................... // Parking Ticket (print-out document) designer TD // ......................................................... // Predefine document Layout (e.g. parking ticket) in advance and stroe it for quick and easy use // in opposite to the above "single" commands you need only one or a few commands at vending time. // Stored text is just send to printer once the printing command is issued // stored commands within the text are interpreted and executed right at the place (in ticket) they are // example: start bold, , stop bold // Predefinition of up to 16 ticket Layouts is possible, 0...1280 byte each // Number 0..15, al keept non-volatile // up to 8 dynamic values can be defined in the template ("print val3 here") and will be sent with printing command // example: print current time at this point (the time of printing not the storage time!!) // obsolete //virtual void pri_startTicketDesign(void) const =0; // start for every new printer document, reseting collecting buffer // all further functions write/append text, numbers and command to the ticket-buffer, up to 1278 bytes allowed // return val of the appending functions: true=ok false=too long, buffer full // obsolete //virtual int pri_TD_getCurrentSize(void) const =0; // retval: 0...1278 // obsolete //virtual bool pri_TD_addText(QByteArray text) const =0; // example: pri_TD_addText("Hello") const =0; // example: pri_TD_addText(tempStr) const =0; // retval: true=ok false=too long, buffer full // obsolete //virtual bool pri_TD_addValue(int val) const =0; // +/- 0...2^(31) // obsolete //virtual bool pri_TD_addNewLine(void) const =0; // obsolete //virtual bool pri_TD_addSign(char sign) const =0; // example: '.' ' ' 0x20 'W' '$' // obsolete //virtual bool pri_TD_addCommand(char group, char attribute, char p1, char p2, char p3, char p4, char p5) const =0; // always add 8 byte to the ticket layout: ESC & group & attribute & parameter1...5 /* complete list of possible commands: group 50 : paper attribute 10 : move forward p1: wayInMm p2: direction attribute 11 : cut p1: kind of, 1=full 2=partial, 3=eject attribute 12 : new line(s) p1: nr of lines 1...100 group 51 : fonts attribute 10 : kind of font see description above p1: 0...8 attribute 11 : font size p1: 6...20 attribute 12 : font width p1: 0...4 attribute 13 : font heigth p1: 0...7 attribute 14 : switch bold print on/off p1: 0=off 1=on attribute 15 : switch invers print on/off p1: 0=off 1=on attribute 16 : switch underlined print on/off p1: 0=off 1=on group 52 : print graphics attribute 10 : print barcode with dynamic data 6 and 7 p1...p5 = kindOf, withText, offset, rotation, dataLeng, see description above attribute 11 : print QRcode with preset data attribute 12 : print Logo p1=nrOfLogo, p2=offset group 53 : print dynamics attribute 10 : p1: 1...8 = print dynData 0..7 at this place */ // obsolete //virtual char prn_clearDocument(uint8_t documentNumber) const =0; // clear memory buffer for ONE document // function takes a second! don't send right before "store doc" // obsolete //virtual bool prn_store_Document(uint8_t documentNumber ) const =0; // send the predefined Layout (generated with above TD functions) to DeviceController to save // documentNumber=0...15 // maximal 1280 bytes each // allowed: 0x20...0xFF, 0x0A, 0x0C, 0x1B (LF, CR, Esc) // 0x1B=start of embedded command (next 7bytes = command) // with a print command a set of 8 dynamic strings can be sent // the place in the ticket layout is predefined (already in DC memory) // the dynamics are first calculated at printing time // obsolete //virtual bool prn_printDocument(uint8_t documentNumber, struct T_dynDat *dynTicketData) const =0; // 36 // $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ // Mifare Card Reader // $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ virtual void mif_readerOn(bool on) const =0; virtual bool mif_cardIsAttached(void) const =0; virtual bool mif_isMifarePowerOn(void) const =0; virtual void request_MifareReaderState() const =0; virtual void request_MifareCardType() const =0; virtual void request_MifareAtbType() const =0; virtual void request_MifareID() const =0; virtual void request_MifareData(uint8_t dataBlockNumber) const =0; //virtual void request_MifareData() const =0; // dataBlockNumber must be 0....11, returns 64byte of data virtual bool test_serialMux2isSetToMifare(void) const =0; virtual void mif_creatAtbCard(uint8_t cardType) const =0; /* data description: byte 0: current read state: 0=power off 1=reader-fault 2=ready 3=just reading 4=read complete 5=read partial, removed too early 6=state unknown byte 1,2: read data length from card 3: 1=reader is OK (reported serial nr is OK) 0=wrong or no reader 4...15: reader version, expected "ATB25-1.8" byte16: 1=card is present 0:not 17: 0 18: card type reported from reader 19: 1=allowed card type 0=not 20: card size: 1 or 4 (dec) = card size 21: LengthOfUID: 4 or 7 (dec) (byte) 22: UID 8 byte in hex byte 30: sector logged: 0 byte 31: current sector: 0 byte 32: result, always 0 */ virtual uint8_t mif_returnReaderStateAndCardType(uint8_t *buf, uint8_t maxBufferSize) const =0; // retval 0=OK 1=error host buffer too small virtual bool mif_readerIsOK(void) const =0; virtual bool mif_cardAttached(void) const =0; virtual uint8_t mif_readResult(void) const =0; // result: 0: unknown or still in progress // 1: card read successful // 2: reading error //virtual void mif_clearDataBuffer(void) const =0; virtual QString mif_cardUID(void) const =0; // returns string with 8 byte //virtual bool mif_isBlockAvailable(uint8_t blkNr) const =0; //blkNr=0...11 //virtual uint32_t mif_getAvailableDataBlocks(void) const =0; // bit0=1 if block 0 = valid ...up to ... bit 11=1 if block 11=read virtual uint8_t mif_getCardDataDec(uint8_t blkNr, uint8_t *buf, uint8_t maxBufferSize) const =0; virtual QString mif_getCardDataStr(uint8_t blockNumber) const =0; // with blockNumber=0...11 // read mifare data independant from blocks //virtual uint16_t mif_getNrOfAvailableDataBytes(void) const =0; //virtual bool mif_getCardData768byteDec(uint8_t *buf, uint16_t bufferSize) const =0; //virtual bool mif_getCardDataDec(uint16_t fromAddr, uint16_t toAddr, uint8_t *buf, uint16_t bufferSize) const =0; //virtual QString mif_getCardDataStr(bool useHexFormat, char seperator) const =0; // 16 // $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ // Credit Card Terminal // $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ virtual void credit_switchPower(bool on) const =0; // the same as modem power virtual bool cred_isCreditPowerOn(void) const =0; virtual bool test_serialMux2isSetToCredit(void) const =0; virtual void credit_switchWake(bool WAKEACTIVE) const =0; // 4 // $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ // Modem // $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ virtual void mod_switchPower(bool on) const=0; virtual bool mod_isGsmPowerOn(void) const =0; virtual bool test_serialMux1isSetToModem(void) const =0; virtual void mod_switchWake(bool WAKEACTIVE) const=0; // 2 // $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ // MDB Bus // $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ virtual void mdb_switchPower(bool on) const =0; virtual void mdb_switchWake(bool WAKEACTIVE) const =0; virtual bool mdb_WakeINisActive(void) const =0; virtual bool mdb_testIsmdbTxDon(void) const =0; virtual bool mdb_isMdbPowerOn(void) const =0; virtual void request_MDB_Status() const =0; virtual void request_MDB_lastResponse() const =0; virtual bool test_getDO_mdbRXtst(void) const =0; // readback digital outputs of connected devices // these functions are not needed for normal operation // but can be used to test and verify conditions virtual void mdb_sendBusReset(void) const =0; virtual void mdb_sendCommand(uint8_t toMdbDevice, uint8_t mdbCommand) const =0; // send one bus command directly over mdb bus, refer to mdb manual for commands // this command is not needed in normal operation, just for new or special things virtual void mdb_sendMessage(uint8_t toMdbDevice, uint8_t mdbCommand, uint8_t nrOfData, uint8_t *dataBuffer) const =0; // nrOfData = sizeOf(dataBuffer) maximal 34 byte according mdb specs // same as mdb_sendCommand, just with data virtual bool mdb_busIsReadyToWork() const =0; virtual bool mdb_deviceVoltageOK() const =0; virtual bool mdb_busVoltageOk() const =0; virtual uint8_t mdb_getLastDeviceResponse(uint8_t *fromDevice, uint8_t *lastRequest, uint8_t *responseLength, uint8_t *responseBuffer) const =0; // fromDevice: device nr from which data was requested 0,1,2,3 // lastRequest: sent mdb command // responseLength: nr of payload data (after mdb-ack) 0...34 // responseBuffer holds payload data (answer from mdb device) // return val: mdb result of this request: 1=got ACK 2=got 3xNAK 3=no or bad response 4:got Data (after ACK) // 15 // $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ // Coin Changer, Checker (EMP) // $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ virtual void request_EMP_allParameters() const =0; virtual void request_EMP_lastCoin() const =0; virtual uint8_t emp_returnLastCoin(uint16_t *value, uint8_t *signal) const =0; // use for changer // ---------------------------------- Electronic Coin Validator EMP ----------------------------------------- virtual void emp_sendSettings(uint16_t coinAcceptance, uint8_t tokenChannel, uint16_t *coinDenomination ) const =0; // coinAcceptance: bit0=coin1 (lowest donomination) bit15=coin16 bitH=accept bit L = deny coin (no validation) // tokenChannel 0...31: if this signal comes from emp then a token was inserted // coinDenomination = array of 16 coin values (e.g. 5, 10, 20...) virtual void emp_pollingOnOff(uint8_t on) const =0; virtual void emp_startCoinAcceptance(void) const =0; virtual void emp_stopCoinAcceptance(void) const =0; virtual void emp_getAllParameters(struct T_emp *emp) const =0; // see struct in hwapi.h // usage example: // hwapi *HWaccess const =0; // HWaccess = new hwapi() const =0; // struct T_emp myEmp const =0; // HWaccess->emp_getAllParameters(&myEmp) const =0; // readval=myEmp.pollingRunning const =0; virtual uint8_t emp_chkIfCoinInserted(void) const =0; // retval: 0...16 coins left in FIFO virtual void emp_getNewCoinRecord(uint8_t *valid, uint8_t *signal, uint8_t *error, uint16_t *value) const =0; // with every call ONE coin is taken out of FIFO and pointer decremented // valid: should be 1 // signal: comes right from coin checker, 0...15 (0=first programmed coin type) 0xFF=no signal // error: was reported from EMP as dynamic signal right after coin insertion (instead of // coin signal), example: 3=unknown coin 4=coin is blocked by host. 0xFF=no error // value: of the coin. Depends on parameter "coinDenomination" in function "emp_sendSettings" // if coinDenomination[coin 0..15] = 0 then the value programmed in coin checker is taken // if coinDenomination > 0 then this value is taken. // Useful in case of two currencies (adapt to local currency) or for token. // function gives more details as "emp getLastCoin()" but "emp getLastCoin()" is easier to use // alternativ to emp_getNewCoinRecord( ): virtual uint8_t emp_giveLastCoin(uint16_t *value, uint8_t *signal) const =0; // retval: 0: NO coin stored 1: valid coin 2: got wrong coin or coin denied // value: if retval1: value of the coin if reval=2: error number // 0xFF means NO error or NO signal (as 0 is a valid error/signal) // signal: channel nr reported from checker 0...15 // 11 // $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ // Coin blocker, Coin Escrow, Coin reject // $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ virtual void shut_move(bool open) const =0; virtual void esc_moveFlaps(uint8_t flap ) const =0; // 0: close both 1: open take-flap 2: open return virtual void coin_switchRejectMotor(uint8_t dir) const =0; virtual bool coid_isAttached(void) const =0; virtual bool coin_escrowIsOpen(void) const =0; virtual bool cash_getRejectMotorHomePos(void) const=0; virtual bool coin_shutterIsOpen(void) const =0; virtual bool coin_shutterTestOutput(void) const =0; virtual uint8_t coin_escrowFlapOpened(void) const =0; // retval: 1:return flap is open 2:take flap is open 0:closed virtual void shut_openOnce(void) const =0; // and close automatic after shutter time virtual void shut_openForCoin(bool start) const =0; // open flap if coin is attached // once process is started it runs until stop command virtual void shut_sendOpeningTime(uint16_t timeIn_ms ) const =0; // after this time without retrigger the flap is closed virtual void esc_takeMoney(void) const =0; // and close automatically after escrow time (1s) virtual void esc_returnMoney(void) const =0; // and close automatically after escrow time (1s) virtual void coin_rejectCoins(void) const =0; // 15 // $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ // MDB Bill evaluator // $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ // $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ // doors, locks, cashboxes // $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ virtual void lock_switchContactPower(bool on) const =0; virtual bool door_isContactPowerOn(void) const =0; virtual uint8_t door_getLocks(void) const =0; // retval bit0: upper lever is up (=open) // bit1: upper lever is down (=locked) // bit2: lower lever is up // bit3: lower lever is down (=locked) virtual bool door_upperDoorIsLocked(void) const =0; virtual bool door_upperDoorIsUnlocked(void) const =0; virtual uint8_t lock_switchUpperLock(uint8_t dir) const =0; // dir 0=off 1=up 2=down // move lock until stop cmd (0) virtual uint8_t lock_openUpperDoor(void) const =0; // Locks stops automatically at end switch or by timeout virtual uint8_t lock_closeUpperDoor(void) const =0; // Locks stops automatically at end switch or by timeout virtual uint8_t door_getSwitches(void) const =0; // retval: bit0: upper door 1: low door 2:vault door virtual bool door_isUpperDoorOpen(void) const =0; virtual bool door_lowerDoorIsLocked(void) const =0; virtual bool door_lowerDoorIsUnlocked(void) const =0; virtual uint8_t lock_switchLowerLock(uint8_t dir) const =0; // dir 0=off 1=up 2=down // move lock until stop cmd (0) virtual uint8_t lock_getDO_motors(void) const =0; // bit0: upper lock forward bit 1 backward // bit2: lower lock forward bit 3 backward virtual uint8_t lock_openLowerDoor(void) const =0; // there's no closing function as Lock always makes one complete cycle and can be locked again immed. virtual uint8_t lock_closeLowerDoor(void) const =0; virtual bool door_isLowerDoorOpen(void) const =0; virtual uint8_t vault_getSwitches(void) const =0; // retval bit0: cash box, bit 1: bill box virtual bool vault_isVaultDoorOpen(void) const =0; virtual void lock_switchVaultDoor(void) const =0; virtual bool vault_isCoinVaultIn(void) const =0; virtual bool vault_isBillVaultIn(void) const =0; // 21 // $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ // LEDs, Barrier, Alarm, Relais, Aux // $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ virtual void led_switchLedIllumination(uint8_t on) const = 0; virtual void led_switchLedCoinbassin(uint8_t on, uint8_t ton, uint8_t tof) const =0; virtual bool led_coinIsOn(void) const =0; // read back digital output from DC-uC-Port virtual bool led_frontIsOn(void) const =0; virtual void led_switchLedService(uint8_t on) const =0; // on=1 off=0 virtual bool led_insideIsOn(void) const =0; virtual void led_switchLedPaper(uint8_t on, uint8_t ton, uint8_t tof) const =0; virtual bool led_ticketIsOn(void) const =0; virtual void led_switchLedStart(uint8_t on, uint8_t ton, uint8_t tof) const =0; virtual bool led_StartIsOn(void) const =0; virtual void led_switchLedPinPad(uint8_t on, uint8_t ton, uint8_t tof) const =0; virtual bool led_pinIsOn(void) const =0; virtual void fan_switchFan(bool on) const =0; virtual void alarm_switchSiren(bool on) const =0; virtual bool fan_isOn(void) const =0; virtual bool siren_isOn(void) const =0; virtual void bar_OpenBarrier(bool open) const =0; virtual bool bar_relayIsOn(void) const =0; virtual bool bar_optoIn1isOn(void) const =0; virtual bool bar_optoIn2isOn(void) const =0; virtual void aux_power(bool on) const =0; virtual bool aux_powerIsOn(void) const =0; virtual void aux_setUsage(uint8_t PinDirection) const =0; virtual void aux_setOutputs(uint8_t PinIsHigh) const =0; virtual bool aux_isAuxPowerOn(void) const =0; virtual uint8_t aux_getAuxInputs(void) const =0; // ------------------------------------------------------------------------------------ // 27.3.2023: Use Device-Controller's Bootloader to send hex-file // ------------------------------------------------------------------------------------ virtual void bl_rebootDC(void) const =0; virtual void bl_startBL(void) const =0; // send command within 4s after DC power-on, otherwise bl is left virtual void bl_checkBL(void) const =0; // send command to verify if bl is up virtual bool bl_isUp(void) const =0; // return true is bl is up and running // also initializes "sendFile" virtual void bl_sendAddress(uint16_t blockNumber) const=0; // send start address, nr of 64byte-block, start with 0 // will be sent only for following block-numbers: // 0, 1024, 2048, 3072 and 4096, so basically every 64kByte // for other addresses nothing happens virtual uint8_t bl_wasSendingAddOK(void) const=0; // return val: 0: no response by now 1:error 10: OK virtual void bl_openBinary(void) const=0; // to be used within CashAgent, momentary not processed virtual void bl_sendDataBlock(uint8_t length, uint8_t *buffer) const=0; // send 64 byte from bin file virtual void bl_sendLastBlock(void) const=0; // send this command after all data are transfered virtual uint8_t bl_wasSendingDataOK(void) const=0; // return val: 0: no response by now 1:error 10: OK virtual void bl_stopBL(void) const=0; // leave BL and start (the new) application //virtual bool bl_isDiagAvailable(void) const=0; //virtual QString dc_getDiagText(void) const=0; // Komplett-schreib Funktion, noch nicht getestet // Nachteil: keine Rückmeldung wie lang's noch dauert //virtual void bl_startSending(void) const=0; // call once after BL is working and file is loaded //virtual void bl_sendFile(void) const=0; // call cyclic while loading bin-file to bootloader // ------------------------------------------------------------------------------------ // 6.4.2023: new functions for coin collection and printing // some new system functions // ------------------------------------------------------------------------------------ virtual bool rtc_setTimeDateDirect(struct Trtc_DateTime *DateTime) const=0; // return true if sending, false if cmd-stack is full virtual bool rtc_getExtendedTime(uint8_t *leng, uint8_t *data) const=0; /* buf[0]=GlobTime.Hours; buf[1]=GlobTime.Min; buf[2]=GlobTime.Sec; buf[3]=GlobTime.Year; buf[4]=GlobTime.Month; buf[5]=GlobTime.Day; buf[6]=GlobTime.DOW; buf[7]=' '; // immer auf 32bit auffüllen sonst Speicherproblem beim Master! uitmp=GlobTime.MinOfDay; buf[8]=swl_getOneByteFromUint(uitmp, 0); buf[9]=swl_getOneByteFromUint(uitmp, 1); buf[10]=' '; buf[11]=' '; ultmp=GlobTime.SecOfDay; buf[12]=swl_getOneByteFromUlong(ultmp, 0); buf[13]=swl_getOneByteFromUlong(ultmp, 1); buf[14]=swl_getOneByteFromUlong(ultmp, 2); buf[15]=swl_getOneByteFromUlong(ultmp, 3); buf[16]=swl_isLeap(GlobTime.Year); buf[17]=swl_getNextLeapYear(GlobTime.Year); buf[18]=swl_getLastLeapYear(GlobTime.Year); buf[19]=swl_hoursOfThisWeek(GlobTime.DOW, GlobTime.Hours); uitmp=swl_minutesOfThisWeek(GlobTime.DOW, GlobTime.Hours, GlobTime.Min); buf[20]=swl_getOneByteFromUint(uitmp, 0); // 0=low byte 1=high byte buf[21]=swl_getOneByteFromUint(uitmp, 1); uitmp=swl_hoursOfThisMonth(GlobTime.Day, GlobTime.Hours); buf[22]=swl_getOneByteFromUint(uitmp, 0); buf[23]=swl_getOneByteFromUint(uitmp, 1); uitmp=swl_minutesOfThisMonth(GlobTime.Day, GlobTime.Hours, GlobTime.Min); buf[24]=swl_getOneByteFromUint(uitmp, 0); buf[25]=swl_getOneByteFromUint(uitmp, 1); uitmp=swl_GetDaysOfYear(GlobTime.Year, GlobTime.Month, GlobTime.Day); buf[26]=swl_getOneByteFromUint(uitmp, 0); buf[27]=swl_getOneByteFromUint(uitmp, 1); uitmp=swl_GetHoursOfYear(GlobTime.Year, GlobTime.Month, GlobTime.Day, GlobTime.Hours); buf[28]=swl_getOneByteFromUint(uitmp, 0); buf[29]=swl_getOneByteFromUint(uitmp, 1); buf[30]=0; buf[31]=0; ultmp= swl_GetMinutesOfYear(GlobTime.Year, GlobTime.Month, GlobTime.Day, GlobTime.Hours, GlobTime.Min); buf[32]=swl_getOneByteFromUlong(ultmp, 0); buf[33]=swl_getOneByteFromUlong(ultmp, 1); buf[34]=swl_getOneByteFromUlong(ultmp, 2); buf[35]=swl_getOneByteFromUlong(ultmp, 3); buf[36]=rtc_getSqwaveSettings(); buf[37]=0; buf[38]=0; buf[39]=0; ultmp= 0; // Minutes of the Millenium buf[40]=swl_getOneByteFromUlong(ultmp, 0); buf[41]=swl_getOneByteFromUlong(ultmp, 1); buf[42]=swl_getOneByteFromUlong(ultmp, 2); buf[43]=swl_getOneByteFromUlong(ultmp, 3); dc2prot_setReadData(44, buf); */ virtual bool rtc_getExtendedTime(struct T_extTime *exTime) const=0; virtual bool sys_runCompleteTest(void) const=0; // warning: lasts 20s in one pace // return true if sending, false if cmd-stack is full virtual bool sys_ready4sending(void) const=0; // return true if a Json-file can be sent virtual bool sys_sendJsonFileToDc(uint8_t kindOfFile, uint8_t nrOfTemplate, uint8_t *content ) const=0; // kindOfFile: 1=config, 2=device, 3=cash, 4=serial, 5=time, 6=printer // nrOfTemplate=1...32 if kindOfFile==6 // content = content of the Json file, max 800byte ascii signs // file is 0-terminated // return true if sending, false if cmd-stack is full virtual bool prn_sendDynamicPrnValues(uint8_t *dynPrnVal ) const=0; // dynPrnVal = array of 8 Variables with 8 byte each, come as ascii string // like: char prn_dynPrnVal[8][8]; // return true if sending, false if cmd-stack is full virtual bool prn_printTemplate(uint8_t nrOftemplate) const=0; // print one of the templates loaded by Json prior // nr = 1..32 // return true if sending, false if cmd-stack is full virtual void log_getHoldAccountNumbers(uint8_t *nrOfVals, uint16_t *accNr ) const=0; // returns all acc nrs of the backuped vault records // use: uint16_t backupedAccNumbers[8] virtual bool log_selectVaultRecord(uint16_t accountNr ) const=0; // return true if sending, false if cmd-stack is full // and trigger transfer virtual bool log_chkIfVaultRecordAvailable(void) const=0; // return true if completly received virtual bool log_getVaultRecord(struct T_vaultRecord *retVR) const=0; // which was selected by: log_selectVaultRecord() // to be forwarded to Ismas virtual bool prn_printAccountReceipt(void) const=0; // return true if sending to DC OK, false if cmd-stack is full virtual bool prn_printTestTicket(void) const=0; // return true if sending to DC OK, false if cmd-stack is full virtual bool cash_startPayment(uint32_t amount) const=0; // 17.4.23TS: extended to 32bit virtual uint8_t cash_paymentProcessing(void) const=0; // run this function periodically while coin payment process to generate necessary signals // return value: // 0: stopped 1: starting up 2: coin collection // 3: finished by User (Push button) 4: finished, Max-Value collected // 5: finished by escrow // 10,11: error cannot start // 12: timeout while payment, coins returned // 13: stopped by unexpected error virtual uint32_t getInsertedAmount(void) const=0; virtual uint16_t getLastInsertedCoin(void) const=0; virtual bool getAllInsertedCoins(uint16_t *types, uint16_t *values) const=0; // all inserted coins (max 64) since "cash_startPayment" virtual bool cash_cancelPayment(void) const=0; // and return coins virtual bool cash_stopPayment(void) const=0; // and keep coins in escrow // after ticket/goods issue: virtual bool vend_success(void) const=0; // conclude payment process, encash all inserted coins to vault. Printing was successful // if possible return change virtual bool vend_failed(void) const=0; // conclude payment process and return all inserted coins virtual uint8_t mif_getCardType(QString *cardholder) const=0; // return 1,2,3,4 = upper, lower access card, printer test, coin test // cardholder: 7byte Name-String virtual uint64_t sys_getWakeSource(void) const =0; // retval: 6 bytes, bit coded, 1=event keeps DC awake virtual uint8_t sys_getWakeReason(void) const=0; // Master was woken by following reason: // 1: MDB Event // 2: Coin Event // ( 3: Master Event) - will not set the wake line // ( 4: 32s pulse) - will not set the wake line // 5: Door Event // ( 6: Diag Event) - will not set the wake line // 7: 30min-Pulse for HB virtual void sys_getDeviceConditions(uint8_t *leng, uint8_t *data) const=0; /* outBuf[0]=modCond.ram; outBuf[1]=modCond.intEe; outBuf[2]=modCond.extEe; outBuf[3]=modCond.rtc; outBuf[4]=modCond.boardHw; outBuf[5]=modCond.printer; outBuf[6]=modCond.modem; outBuf[7]=modCond.signal; outBuf[8]=modCond.regist; outBuf[9]=modCond.mdbBus; outBuf[10]=modCond.coinChecker; outBuf[11]=modCond.coinEscrow; outBuf[12]=modCond.mifareReader; outBuf[13]=modCond.creditTerm; outBuf[14]=modCond.coinReject; outBuf[15]=modCond.coinSafe; outBuf[16]=modCond.billSafe; outBuf[17]=modCond.voltage; outBuf[18]=modCond.temper; outBuf[19]=modCond.poweronTest; outBuf[20]=modCond.doorState; outBuf[21]=modCond.doorWasOpened; outBuf[22]=modCond.changer; outBuf[23]=modCond.coinBlocker; outBuf[24]=modCond.billReader; outBuf[25]=modCond.ResetReason; outBuf[26]=modCond.allModulesChecked; outBuf[27]=modCond.alarmState; outBuf[28]=0; outBuf[29]=0; */ virtual void sys_getDeviceConditions(struct T_moduleCondition *devCond) const=0; virtual void sys_getDynMachineConditions(uint8_t *leng, uint8_t *data) const=0; /* outBuf[pBuf++]=dynCond.allDoorsDebounced; outBuf[pBuf++]=dynCond.openedAuthorized; outBuf[pBuf++]=dynCond.CBinDebounced; outBuf[pBuf++]=dynCond.upperDoor; outBuf[pBuf++]=dynCond.middleDoor; outBuf[pBuf++]=dynCond.lowerDoor; outBuf[pBuf++]=dynCond.coinBox; outBuf[pBuf++]=dynCond.billBox; outBuf[pBuf++]=dynCond.modeAbrech; outBuf[pBuf++]=dynCond.onAlarm; outBuf[pBuf++]=dynCond.nowCardTest; outBuf[pBuf++]=dynCond.nowPayment; outBuf[pBuf++]=dynCond.lastMifCardType; outBuf[pBuf++]=dynCond.lastSDoorState; outBuf[pBuf++]=dynCond.lastVDoorState; outBuf[pBuf++]=dynCond.lastCBstate; outBuf[pBuf++]=dynCond.paymentInProgress; outBuf[pBuf++]=0; uitmp=dynCond.U_Batt; outBuf[pBuf++]=swl_getOneByteFromUint(uitmp, GETLOWBYT); outBuf[pBuf++]=swl_getOneByteFromUint(uitmp, GETHIGHBYT); uitmp=dynCond.Temperatur; outBuf[pBuf++]=swl_getOneByteFromUint(uitmp, GETLOWBYT); outBuf[pBuf++]=swl_getOneByteFromUint(uitmp, GETHIGHBYT); uitmp=dynCond.nrCoinsInBox; // send seperate also outBuf[pBuf++]=swl_getOneByteFromUint(uitmp, GETLOWBYT); outBuf[pBuf++]=swl_getOneByteFromUint(uitmp, GETHIGHBYT); ultmp=dynCond.amountInBox; // send seperate also outBuf[pBuf++]=swl_getOneByteFromUlong(ultmp, GETLOWESTBYT); outBuf[pBuf++]=swl_getOneByteFromUlong(ultmp, GETLOWMID); outBuf[pBuf++]=swl_getOneByteFromUlong(ultmp, GETHIGHMID); outBuf[pBuf++]=swl_getOneByteFromUlong(ultmp, GETHIGHESTBYT); ultmp=dynCond.totalTransVolume; outBuf[pBuf++]=swl_getOneByteFromUlong(ultmp, GETLOWESTBYT); outBuf[pBuf++]=swl_getOneByteFromUlong(ultmp, GETLOWMID); outBuf[pBuf++]=swl_getOneByteFromUlong(ultmp, GETHIGHMID); outBuf[pBuf++]=swl_getOneByteFromUlong(ultmp, GETHIGHESTBYT); ultmp=dynCond.totalNrOfVends; outBuf[pBuf++]=swl_getOneByteFromUlong(ultmp, GETLOWESTBYT); outBuf[pBuf++]=swl_getOneByteFromUlong(ultmp, GETLOWMID); outBuf[pBuf++]=swl_getOneByteFromUlong(ultmp, GETHIGHMID); outBuf[pBuf++]=swl_getOneByteFromUlong(ultmp, GETHIGHESTBYT); // 36 outBuf[pBuf++]=dynCond.jsonValid_config; outBuf[pBuf++]=dynCond.jsonValid_device; outBuf[pBuf++]=dynCond.jsonValid_cash; outBuf[pBuf++]=dynCond.jsonValid_print; outBuf[pBuf++]=dynCond.jsonValid_serial; outBuf[pBuf++]=dynCond.jsonValid_time; outBuf[pBuf++]=dynCond.lastFileType; outBuf[pBuf++]=0; */ virtual void sys_getDynMachineConditions(struct T_dynamicCondition *dynMachCond) const=0; // content of Cashbox virtual uint32_t cash_getAmountInVault(void) const=0; virtual uint16_t cash_getNrCoinsInVault(void) const=0; virtual uint8_t prn_getPrintResult() const=0; // return: 0: unknown // 1: OK - last template was printed succesful // 2: error - last template was not printed // in case of print-error get detailed error: virtual uint8_t prn_getCurrentPrinterState() const=0; // 0: printer OK // bit0: near paper end bit1: no paper // bit2: temperature error bit3: error head open // bit4: paper jam in cutter // bit6: no response bit7: serial rec. error // bit5: printer not ready virtual void sys_sendDeviceParameter(struct T_devices *deviceSettings) const=0; virtual void sys_restoreDeviceParameter(struct T_devices *deviceSettings) const=0; virtual bool sys_areDCdataValid(void) const=0; virtual bool sys_sendingTest(void) const =0; virtual void prn_requestCurrentDynData(void) const =0; virtual bool prn_getCurrentDynamicPrnValuesFromDC(uint8_t *dynPrnVal ) const =0; // which was sent with: bool prn_sendDynamicPrnValues(uint8_t *dynPrnVal ) const override; virtual bool prn_dynDataAreEqual(uint8_t *buf) const =0; virtual bool prn_printKombiticket(uint8_t nrOfKombi) const=0; // print four of the templates loaded by Json prior // nr = 1..8 virtual void lock_triggerUpperSolenoid(void) const =0; virtual void lock_triggerLowerSolenoid(void) const =0; signals: virtual void hwapi_templatePrintFinished_OK(void) const=0; virtual void hwapi_templatePrintFinished_Err(void) const=0; virtual void hwapi_coinCollectionJustStarted(void) const=0; virtual void hwapi_coinCollectionAborted(void) const=0; virtual void hwapi_gotNewCoin(void) const=0; virtual void hwapi_payStopByMax(void) const=0; virtual void hwapi_payStopByPushbutton(void) const=0; virtual void hwapi_payStopByEscrow(void) const=0; virtual void hwapi_payStopByError(void) const=0; virtual void hwapi_payStopByTimeout(void) const=0; virtual void hwapi_payCancelled(void) const=0; virtual void hwapi_coinProcessJustStopped(void) const=0; }; // History // 11.10.2021: V1.0 222 functions // 23.12.2021: V1.1 added block-parameter to function "read mifare data" // 30.12.2021: V1.2 added function: mif_clearDataBuffer(), mif_isBlockAvailable(uint8_t blkNr) and mif_getAvailableDataBlocks() // 1.1.2022: V1.3 Mifare extended. ( background: read 16 x 48byte from card to DC, read 12 x 64byte from DC to CA) // new: read full card with 768bytes from HWapi without block borders // added: mif_getNrOfAvailableDataBytes mif_getCardData768byteDec(uint8_t *buf, uint16_t bufferSize) // mif_getCardDataDec(uint16_t fromAddr, uint16_t toAddr, uint8_t *buf, uint16_t bufferSize) // mif_getCardDataStr(bool useHexFormat, char seperator) // 29.03.2023: V3.1 some extensions for PSA1256_ptu5, // V3.2 Bootloader improvement // 12.04.2023: V3.3 new features extended: loading and using Json-files, cash-collection, cash-data-logging // 14.04.2023: V3.4 new features extended: sys_getDynMachineConditions, sys_getDeviceConditions and // rtc_getExtendedTime return struct in addition. New function to select and get VaultRecord // // 19.04.2023: V3.5 new function: sys_getWakeReason(); // 17.05.2023: V3.6 new function: cash_isCollectionActive(), cash_isPayProcessActive() // new signals: hwapi_coinCollectionJustStopped, hwapi_coinCollectionJustStarted // getAllInsertedCoins() fixed, also in datif and storeINdata //#define HWINF_iid "Atb.Psa2020.software.HWapi/3.1" //#define HWINF_iid "Atb.Psa1256ptu5.software.HWapi/3.1" //#define HWINF_iid "Atb.Psa1256ptu5.software.HWapi/3.3" //#define HWINF_iid "Atb.Psa1256ptu5.software.HWapi/3.4" //#define HWINF_iid "Atb.Psa1256ptu5.software.HWapi/3.5" #define HWINF_iid "Atb.Psa1256ptu5.software.HWapi/3.6" Q_DECLARE_INTERFACE(hwinf, HWINF_iid) #endif