diff --git a/plugins/interfaces.h b/plugins/interfaces.h new file mode 100644 index 0000000..288d533 --- /dev/null +++ b/plugins/interfaces.h @@ -0,0 +1,1350 @@ +#ifndef INTERFACE_H +#define INTERFACE_H + +#include + +#define THIS_IS_CA_MASTER + +struct T_emp +{ + + // Fixdata from EMP: + uint8_t shaft; // = changer level + uint16_t countryCode; + uint8_t scale; + uint8_t decimals; + uint8_t coinValues[16]; + uint16_t routing; + + // Master specs: + uint8_t gotSetup; // 1: got specifications from master 0: no specs + uint16_t coinAccept; // bit 0 = coin1 bit H=accept + uint8_t tokenChannel; + uint16_t denomination[16]; + + // dynamic: + uint8_t state; // step counter of EMP (electronic coin checker) FSM (finite state machine): + // 0=start command + // 1=powered, do emp ini, send reset + // 2=delay + // 3=wait for response, requesting status after response + // 4,5 through, startup + // 6: wait for status + // 7: through, startup + // 8: IDLE state. EMP is up and ready, polling is running + // 9: polling on, payment not yet on + // 10: payment, check coins + // 11: through + // 12: wait 1s for last coin + // 90: stop all, 1s delay + // 99: off, all stopped + + + uint8_t pollingRunning; + uint8_t paymentRunning; + +}; + +struct Trtc_DateTime +{ + uint8_t rtc_hour; + uint8_t rtc_min; + uint8_t rtc_sec; + uint8_t rtc_dayOfMonth; + uint8_t rtc_month; + uint8_t rtc_year; + uint8_t rtc_dayOfWeek; +}; + +struct Tprn_hw_state +{ + // hardware (IO's) + bool powerRdBk; // prn pwr is on + bool rsSwOk; // serial switch (printer or modem) is set to printer + bool rsDrvOk; // RS232 converter for PTU, Printer and Modem in on + + bool ReadyLine; // HW signal from printer showing ready + bool inIdle; // powered and free from errors + bool paperNearEnd; // paper roll runs out + bool noPaper; + bool ErrorTemp; + bool HeadOpen; + bool cutterJam; + bool noResponse; // printer is not connected, cable broken, wrong baudrate + bool badResponse; +}; + + struct Tprn_currentSettings +{ + uint8_t currFont; + uint8_t currSize; + uint8_t currHeigth; + uint8_t currWidth; + bool nowBold; + bool nowInvers; + bool nowUnderlined; + uint8_t currDensity; + uint8_t currSpeed; + bool nowAligned; +}; + +// obsolete + struct T_dynDat +{ + uint8_t licensePlate[8]; + uint8_t vendingPrice[8]; + uint8_t parkingEnd[8]; + uint8_t currentTime[8]; + uint8_t currentDate[8]; + uint8_t dynDat5[8]; + uint8_t dynDat6[8]; + uint8_t dynDat7[8]; +}; + + +struct T_vaultRecord +{ + + // Kassenbeleg (Abrechnungsdatensatz = Kassenwechsel-Datensatz) + char startbuffer[4]; // Psa> // never move or change this 1st entry + uint16_t AccountingNumber; + uint16_t CUNU; + uint16_t MANU; + uint16_t resint1; + //uint16_t resint2; + + char label1buffer[4]; // tim> + uint8_t year; + uint8_t month; + uint8_t dom; + uint8_t hour; + uint8_t min; + uint8_t sec; + uint8_t DoW; + uint8_t reschar3; + + char label2buffer[4]; // abs> + uint32_t AbsIncome1; + uint32_t AbsReserve; + uint32_t AbsNrOfCuts; + +//16 + char label3buffer[4]; // mw > + + // Verkauf, Tür zu: + uint32_t VKcoinsInserted[16]; // nur für Wechsler, soviel wurde eingeworfen + uint32_t VKcoinsReturned[6]; // nur für Wechsler, Anzahl Münzen pro Typ, soviel wurde zurückgegeben +//88 + + // Service, Tür offen: + uint16_t ServCoinsInserted[16]; // nur für Wechsler, soviel wurde eingeworfen + uint16_t ServCoinsReturned[6]; // nur für Wechsler, Anzahl Münzen pro Typ, soviel wurde zurückgegeben + uint16_t resint3; + uint16_t resint4; + uint16_t currentTubeContent[6]; // nur für Wechsler, aktueller Füllstand + uint16_t resint5; + uint16_t resint6; +// 56 + + char label4buffer[4]; // box> + uint16_t coinsInVault[16]; + uint16_t billsInStacker[8]; +// 48 + + char label5buffer[4]; // val> + // actually constant unless exchange rate is changed + uint16_t coinDenomination[16]; // 5..50000 (z.B. 2? sind in Ungarn 760Ft) + uint16_t billDenom[8]; + uint16_t tubeDenom[6]; + uint16_t exchangeRate; + uint16_t resint9; + +// 64 + + char endofblock[4]; // end> + +// 316 byte Block im Speicher + +}; + +struct T_moduleCondition +{ + // store conditon of all system components, hold in RAM + // 0 means unknown, not yet tested/used + // 1 means OK + // 50..99 = HINT / Notification + // 100..150 = WARNING + // 200..250 = ERROR + + uint8_t ram; + uint8_t intEe; + uint8_t extEe; + + uint8_t rtc; // 1: time/date OK 100: time not plausible 200: hardware error + uint8_t boardHw; + uint8_t printer; + uint8_t modem; + + uint8_t signal; // 1...99 + uint8_t regist; // 100:not 1:reg 2:ping OK 3:gotTime + uint8_t mdbBus; + uint8_t coinChecker; // EMP, OMP or mei-cashflow + + uint8_t coinEscrow; + uint8_t mifareReader; + uint8_t creditTerm; + uint8_t coinReject; + + uint8_t coinSafe; + uint8_t billSafe; + uint8_t voltage; // 1:11..14V + uint8_t temper; + + uint8_t poweronTest; + uint8_t doorState; // 1: alles zu 200: t?r offen + bit1(S) +bit2(CB) + bit3(CB) + uint8_t doorWasOpened; // 1: all doors are closed 200: any door was just opened + uint8_t changer; // can only be tested by usage + + uint8_t coinBlocker; // can only be tested by usage + uint8_t billReader; // can only be tested by usage + uint8_t ResetReason; + uint8_t allModulesChecked; + + uint8_t alarmState; + uint8_t res11; + uint8_t res12; + uint8_t res13; +// 31 +}; + +struct T_dynamicCondition +{ + char allDoorsDebounced; + char openedAuthorized; + uint8_t CBinDebounced; // 0:fehlt 1:drin + char upperDoor; // 99: undefined 0:closed 1:open + char middleDoor; // 99: undefined 0:closed 1:open + char lowerDoor; // 99: undefined 0:closed 1:open + char reserve; + char billBox; + char modeAbrech; + char onAlarm; // 0:alarm aus 1:alarm 2:alarm mit Sirene 3: Sirenentest + char nowCardTest; + char nowPayment; // not used, always 0 + char lastMifCardType; + uint8_t lastSDoorState; + uint8_t lastVDoorState; + uint8_t lastCBstate; + char paymentInProgress; + // 0: stopped by timeout + // 1: running 2: wait4lastCoin + // 3: payment stopped manually, coins in Escrow + // 4: payment stopped autom, amount collected, coins in Escrow + // 5: payment stopped, escrow full, coins in Escrow + // 6: coins encashed 7:coins returned + // 8: CoinChecker or MDB on Error + + + char res1; + uint16_t U_Batt; + uint16_t Temperatur; + uint16_t nrCoinsInBox; + uint32_t amountInBox; + uint32_t totalTransVolume; + uint32_t totalNrOfVends; + char jsonValid_config; + char jsonValid_device; + char jsonValid_cash; + char jsonValid_print; + char jsonValid_serial; + char jsonValid_time; + char lastFileType; +// 44 + uint8_t MifCardHolder[8]; + uint8_t resultOfLastTemplPrint; + // 0: unknown or printing in progress + // 1: OK, doc was printed 2: error, doc was not printed + uint8_t lastPrinterStatus; + // 0: printer OK + // bit0: near paper end bit1: no paper + // bit2: temperature error bit3: error head open + // bit4: paper jam in cutter + // bit6: no response bit7: serial rec. error + // bit5: printer not ready + uint8_t startupTestIsRunning; + + //54 +}; + +struct T_extTime +{ + uint8_t Hours; + uint8_t Min; + uint8_t Sec; + uint8_t Year; + uint8_t Month; + uint8_t Day; + uint8_t DOW; + uint8_t res1; + uint16_t MinOfDay; + uint16_t res2; + uint32_t SecOfDay; + uint8_t isLeapYear; + uint8_t nxtLeapYear; + uint8_t lastLeapYear; + uint8_t hoursOfThisWeek; + uint16_t minutesOfThisWeek; + uint16_t hoursOfThisMonth; + uint16_t daysOfThisYear; + uint16_t GetHoursOfYear; + uint16_t res3; + uint32_t GetMinutesOfYear; + uint8_t getWakeIntvSec; + uint8_t res4; + uint16_t res5; + uint32_t MinutesOfMillenium; + +}; + + +typedef uint8_t UCHAR; +typedef uint16_t UINT; + +struct T_devices +{ + // set by master, used(1) or notused (0) or type 2....20 + + UCHAR kindOfPrinter; // 0:off 1:Gebe + UCHAR kindOfCoinChecker; // 0: without 1=EMP820 2=EMP900 3=currenza c² (MW) + UCHAR kindOfMifareReader; // by now only stronglink SL025 =1 + UCHAR suppressSleepMode; // 0:sleep allowed 1: no sleep + + UCHAR kindOfModem; // 0:off 1:Sunlink + UCHAR kindOfCreditcard; // 0:off 1:Feig NFC + UCHAR CoinEscrow; + UCHAR CoinRejectUnit; + + UCHAR CoinShutter; + UCHAR BillAcceptor; + UCHAR usevaultLock; + UCHAR autoAlarm; // 1: switch on siren for 1min in doors opened unauthorized + + UCHAR autoOpen; // 1: open door covers after valid ATBcard + UCHAR printAccReceipt; // 0/1 + UCHAR printDoorReceipt; + UCHAR printTokenTicket; + + UINT VaultFullWarnLevel; + UINT VaultFullErrorLevel; + +}; + + + +class hwinf +{ + +public: + virtual ~hwinf() {} + + + + // $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ + // Use serial interface and protocol stack in Cashagent-Library + // Sending Output data to DeviceController DC2b + // Sending input requests to DC2 (single or auto-batch) + // Getting input data as receiver payload + // Furthermore the Cashagent-Library answers with status strings about sending and reading result + // $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ + +#ifdef THIS_IS_CA_MASTER + virtual bool dc_openSerial(int BaudNr, QString BaudStr, QString ComName, uint8_t connect) const =0; + // Command: open serial interface + // BaudNr: 0:1200 1:9600 2:19200 3:38400 4:57600 5:115200 + // BaudStr: for exapmle "19200" + // ComName: for example "COM48" + // connect: 0, 1 + + virtual void dc_closeSerial(void) const =0; + // Command: close serial interface in order to save power while power down + // or if another port must be used +#endif + + virtual bool dc_isPortOpen(void) const =0; + // returns true if port open (don't send unless open. Sending to closed port will crash program) + + virtual void dc_autoRequest(bool on) const =0; + // on = true: select that all READ-Requests are sent automatically + // on = false: select that all READ-Requests are sent manually one by one + // Every input information from DC2 must be requested + // ( digital and analog sensors, get time/date, get status information ) + + virtual void dc_requTestResponse() const =0; + // tell DC2 to send a test-string, useful to see if cable and baudrate is OK + + virtual bool dc_readAnswTestResponse() const =0; + // retval: true: test was successful, got right response + + virtual uint8_t dc_isRequestDone(void) const =0; + // retval: 0: request is still in progress + // 1: answer from DC2 was OK + // 2: wrong answer from DC2 + + virtual uint16_t dc_getCompletePayLoad(uint16_t plBufSiz, uint8_t *payLoad) const =0; + // get data back in "payLoad", max 64 byte, can be used for diagnosis + // retval = nr of bytes received. If host buffer too small then + // only plBufSiz bytes are copied to "payLoad" + // plBufSiz­z=size of host buffer + + virtual void dc_setWakeFrequency(uint8_t period) const =0; + // RTC wakes DC2 (and PTU) by hardware signal every 32seconds + // change wake signal period to 1...64s + + virtual void dc_OrderToReset(void) const =0; + // want DC2 to reset (in order to start Bootloader) + +#ifdef THIS_IS_CA_MASTER + virtual QString dc_getSerialState(void) const =0; + // get result of opening-command like "ttyS0 opened with 115200 8N1! + // or error messages like "comport not available..." + // was saved by last opening event, can be passed for 100ms + + virtual void dc_clrSerialStateText(void) const =0; + // clear above text to avoid multiple repetive displaying +#endif + + virtual void bl_sendDataDirectly(uint8_t length, uint8_t *buf) const =0; + // send without protocol frame, needed for the DC bootloader + + virtual uint8_t getRawRecLength(void) const =0; + // only needed if protocol stack in Cashagent-Library is bypassed + + virtual uint8_t getRawReceivedData(uint8_t *receivedData) const =0; + // only needed if protocol stack in Cashagent-Library is bypassed + + virtual QString dc_getSerialParams(void) const =0; + // get DC2 serial settings (not very meaningful as they will not come if different from master settings) + + virtual QString dc_getHWversion(void) const =0; + // get DC2 hardware version + + virtual QString dc_getSWversion(void) const =0; + // get DC2 software version + + virtual QString dc_getState(void) const =0; + // get DC2 status (every OK or any error/warning? ) + + +// ---------------------------------------------------------------------------------------------------------- +// Date and Time +// ---------------------------------------------------------------------------------------------------------- + + virtual uint8_t rtc_getDateTime(struct Trtc_DateTime *rtc_DateTime) const =0; + + virtual uint8_t rtc_setDateTime(void) const =0; + // synch DC2 with PC or PTU system time and date + + virtual void rtc_getTime(uint8_t *hh, uint8_t *mm, uint8_t *ss) const =0; + // get time directly + + virtual void rtc_getDate(uint8_t *yy, uint8_t *mm, uint8_t *dd) const =0; + // get date directly + + virtual uint8_t rtc_getToday(uint8_t *dow, uint16_t *minOfToday, uint32_t *secOfToday) const =0; + // dow=day of week, 1=monday...7 + // minOfToday: 0=midnight...1439= 23:59 + // secOfToday: 0=midnight...86399= 23:59:59 + + virtual bool rtc_isLeapYear(uint8_t *lastLeapYear, uint8_t *NextLeapYear) const =0; + // retval true: this year is leap year + + virtual bool rtc_isLeapYear() const =0; + + virtual void rtc_getWeek(uint8_t *DayOfWeek, uint8_t *HoursOfWeek, uint16_t *MinutesOfWeek) const =0; + // DayOfWeek: 1=monday...7 + // HoursOfWeek: 0=Monday 0:00 o'clock...167=Sunday 23:00 + // MinutesOfWeek: 0=Monday 0:00 o'clock...10079=Sunday 23:59 + + virtual void rtc_getMonth(uint8_t *DayOfMonth, uint16_t *HoursOfMonth, uint16_t *MinutesOfMonth) const =0; + // DayOfMonth: 1...31 + // HoursOfMonth: 0 = 0:00o'clock of 1.day in month up to 743 + // MinutesOfMonth:0 = 0:00o'clock of 1.day in month up to 44639 + + virtual void rtc_getYear(uint16_t *DayOfYear, uint16_t *HoursOfYear, uint32_t *MinutesOfYear) const =0; + // DayOfYear: 1...366 1= 1.Jan of this current year + // HoursOfYear: 0=1.Jan 0:00o'clock ...8783=31.12 23 o'clock + // MinutesOfYear: 0=1.Jan 0:00o'clock ...527039=31.12 23:59 o'clock + + virtual QString rtc_getTimStr(void) const =0; + virtual QString rtc_getDatStr(void) const =0; + virtual QString rtc_getTimDatStr(void) const =0; + + + // UID - unique number, different in every DC + virtual void dc_getUID8byte(uint8_t *buf8byteUid) const =0; + // get 8 single bytes in buffer + + virtual QString dc_getUIDstr() const =0; + // get as string + + virtual uint64_t dc_getUIDnumber(void) const =0; + // get UID as one long number + +// ---------------------------------------------------------------------------------------------------------- +// analogs +// ---------------------------------------------------------------------------------------------------------- + + // Analog values: + virtual uint32_t dc_getTemperature(void) const =0; + // in Sax-Format 0...400 (0=-50,0°C 100=0,0°C 141=20,5°C 400=150,0°C) + + virtual QString dc_getTemperaturStr(void) const =0; + // as string like "-12,5°C" + + virtual uint32_t dc_getVoltage(void) const =0; + // as value in mV, 0...65,535V + + virtual QString dc_getVoltagStr(void) const =0; + // as string in mV + + virtual bool dc_mainFuseIsOk(void) const=0; + // true if 12V fuse is OK + // false: fuse blown, DC will continue working but no 12V device can be used! + +// ------------------------------------------------------------------------------ +// digital outputs +// ------------------------------------------------------------------------------ + + virtual uint8_t lock_switchUpperLock(uint8_t dir) const =0; + // dir 0=off 1=up 2=down + // move lock until stop cmd (0) + + virtual uint8_t lock_switchLowerLock(uint8_t dir) const =0; + // dir 0=off 1=up 2=down + // move lock until stop cmd (0) + + virtual void lock_switchVaultDoor(void) const =0; + + virtual void coin_switchRejectMotor(uint8_t dir) const =0; + + virtual void coin_rejectCoins(void) const =0; + + // LEDs + virtual void led_switchLedService(uint8_t on) const =0; + virtual void led_switchLedPaper(uint8_t on, uint8_t ton, uint8_t tof) const =0; + virtual void led_switchLedPinPad(uint8_t on, uint8_t ton, uint8_t tof) const =0; + virtual void led_switchLedStart(uint8_t on, uint8_t ton, uint8_t tof) const =0; + virtual void led_switchLedCoinbassin(uint8_t on, uint8_t ton, uint8_t tof) const =0; + + virtual void fan_switchFan(bool on) const =0; + virtual void alarm_switchSiren(bool on) const =0; + virtual void bar_OpenBarrier(bool open) const =0; + virtual void ptu_switchWake(bool WAKEACTIVE) const =0; + + virtual void aux_power(bool on) const =0; + virtual void aux_setUsage(uint8_t PinDirection) const =0; + virtual void aux_setOutputs(uint8_t PinIsHigh) const =0; + + virtual void lock_switchContactPower(bool on) const =0; + + virtual void prn_switchPower(bool on) const =0; + + virtual void mif_readerOn(bool on) const =0; + + virtual void mif_creatAtbCard(uint8_t cardType) const =0; + + virtual void mod_switchPower(bool on) const=0; + + virtual void mod_switchWake(bool WAKEACTIVE) const=0; + + virtual void mdb_switchPower(bool on) const =0; + + virtual void mdb_switchWake(bool WAKEACTIVE) const =0; + + virtual void credit_switchPower(bool on) const =0; + // the same as modem power + + virtual void credit_switchWake(bool WAKEACTIVE) const =0; + + virtual void shut_move(bool open) const =0; + + virtual void esc_moveFlaps(uint8_t flap ) const =0; + // 0: close both 1: open take-flap 2: open return + + +// ------------------------------------------------------------------------------ +// door, cashbox and lock switches +// ------------------------------------------------------------------------------ + + virtual uint8_t door_getSwitches(void) const =0; + // retval: bit0: upper door 1: low door 2:vault door + + virtual bool door_isUpperDoorOpen(void) const =0; + + virtual bool door_isLowerDoorOpen(void) const =0; + + virtual bool vault_isVaultDoorOpen(void) const =0; + + virtual uint8_t vault_getSwitches(void) const =0; + // retval bit0: cash box, bit 1: bill box + + virtual bool vault_isCoinVaultIn(void) const =0; + + virtual bool vault_isBillVaultIn(void) const =0; + + virtual uint8_t door_getLocks(void) const =0; + // retval bit0: upper lever is up (=open) + // bit1: upper lever is down (=locked) + // bit2: lower lever is up + // bit3: lower lever is down (=locked) + + virtual bool door_upperDoorIsLocked(void) const =0; + + virtual bool door_upperDoorIsUnlocked(void) const =0; + + virtual bool door_lowerDoorIsLocked(void) const =0; + + virtual bool door_lowerDoorIsUnlocked(void) const =0; + + virtual bool bar_optoIn1isOn(void) const =0; + + virtual bool bar_optoIn2isOn(void) const =0; + + virtual uint8_t aux_getAuxInputs(void) const =0; + + virtual bool ptu_WakeINisActive(void) const =0; + + virtual bool mdb_WakeINisActive(void) const =0; + + virtual bool prn_readyINisActive(void) const =0; + + virtual bool coid_isAttached(void) const =0; + + virtual bool coin_escrowIsOpen(void) const =0; + + virtual bool mif_cardIsAttached(void) const =0; + +//bool hwapi::mod_WakeINisActive(void); + + virtual bool door_isContactPowerOn(void) const =0; + + virtual bool mif_isMifarePowerOn(void) const =0; + + virtual bool mdb_testIsmdbTxDon(void) const =0; + + virtual bool aux_isAuxPowerOn(void) const =0; + + virtual bool mod_isGsmPowerOn(void) const =0; + + virtual bool cred_isCreditPowerOn(void) const =0; + + virtual bool prn_isPrinterPowerOn(void) const =0; + + virtual uint8_t prn_PrnFuseIsOk(void) const=0; + //retval: 0: fuse blown 1: fuse OK 2:unknown as printer power is off + + virtual bool mdb_isMdbPowerOn(void) const =0; + + virtual bool cash_getRejectMotorHomePos(void) const=0; + + virtual uint8_t cash_getLowPaperSensor(void) const=0; + // 0: Sensor sees paper 1: no paper 99: off + + + // ------------------------------------------------------------------------------ + // request commands + // ------------------------------------------------------------------------------ + + // all read-requests can be sent manually by the following functions + // or automatically in background by: void hwapi::dc_autoRequest(bool on) + + + virtual void request_DC2serialConfig() const =0; + // read-request can be sent manually by this function, not needed if auto-request is on + + virtual void request_DC2_HWversion() const =0; + // read-request can be sent manually by this function, not needed if auto-request is on + virtual void request_DC2_SWversion() const =0; + // read-request can be sent manually by this function, not needed if auto-request is on + virtual void request_DC2_condition() const =0; + // read-request can be sent manually by this function, not needed if auto-request is on + virtual void request_DC2_UID() const =0; + // read-request can be sent manually by this function, not needed if auto-request is on + virtual void request_DC2_TimeAndDate() const =0; + // read-request can be sent manually by this function, not needed if auto-request is on + virtual void request_DC2_analogues() const =0; + // read-request can be sent manually by this function, not needed if auto-request is on + virtual void request_DC2_digitalInputs() const =0; + // read-request can be sent manually by this function, not needed if auto-request is on + virtual void request_DC2_digitalOutputs() const =0; + // read-request can be sent manually by this function, not needed if auto-request is on + + // ------------------------------------------------------------------------------ + + // the following device state requests are deployed only if device is powered up: + virtual void request_PrinterHwState() const =0; + virtual void request_PrinterCurrentFonts() const =0; + virtual void request_PrinterStateComplete() const =0; + + virtual void request_MifareReaderState() const =0; + virtual void request_MifareCardType() const =0; + virtual void request_MifareAtbType() const =0; + virtual void request_MifareID() const =0; + virtual void request_MifareData(uint8_t dataBlockNumber) const =0; + //virtual void request_MifareData() const =0; + + virtual void request_MDB_Status() const =0; + virtual void request_MDB_lastResponse() const =0; + virtual void request_EMP_allParameters() const =0; + virtual void request_EMP_lastCoin() const =0; + + + // ------------------------------------------------------------------------------ + // readback digital outputs of connected devices + // these functions are not needed for normal operation + // but can be used to test and verify conditions + // ------------------------------------------------------------------------------ + + + virtual bool test_getDO_mdbRXtst(void) const =0; + // readback digital outputs of connected devices + // these functions are not needed for normal operation + // but can be used to test and verify conditions + + virtual uint8_t lock_getDO_motors(void) const =0; + // bit0: upper lock forward bit 1 backward + // bit2: lower lock forward bit 3 backward + + virtual uint8_t test_serialState(void) const =0; + // test on-board signals for the serials + // serial drv on/off, Serial mux1, Serial mux2 + + virtual bool test_serialIsOn(void) const =0; + + virtual bool test_serialMux1isSetToPrinter(void) const =0; + virtual bool test_serialMux1isSetToModem(void) const =0; + virtual bool test_serialMux2isSetToCredit(void) const =0; + virtual bool test_serialMux2isSetToMifare(void) const =0; + + virtual bool led_coinIsOn(void) const =0; + virtual bool led_frontIsOn(void) const =0; + virtual bool led_ticketIsOn(void) const =0; + virtual bool led_pinIsOn(void) const =0; + virtual bool led_StartIsOn(void) const =0; + virtual bool led_insideIsOn(void) const =0; + + virtual bool fan_isOn(void) const =0; + virtual bool siren_isOn(void) const =0; + virtual bool bar_relayIsOn(void) const =0; + virtual bool ptu_WakeOutIsOn(void) const =0; + + virtual bool aux_powerIsOn(void) const =0; + + virtual bool coin_shutterIsOpen(void) const =0; + virtual bool coin_shutterTestOutput(void) const =0; + + virtual uint8_t coin_escrowFlapOpened(void) const =0; + // retval: 1:return flap is open 2:take flap is open 0:closed + + + +// ------------------------------------------------------------------------------ +// devices are operated by DC +// processes with more then one devices +// timer controlled or long term processes +// ------------------------------------------------------------------------------ + + + virtual void sendDeviceSettings(uint8_t kindOfPrinter, uint8_t kindOfCoinChecker, + uint8_t kindOfMifareReader, uint8_t suppressSleep, + uint8_t kindOfModem, uint8_t kindOfCredit ) const =0; + // enable hardware in device controller: + // kindOfPrinter: 0:off 1: GPT4672 (only this one implemented) + // kindOfCoinChecker: 0:off 1:EMP820 2:EMP900 3: C²_changer + // kindOfMifareReader: 0:off 1: SL025 (only this one implemented) + // suppressSleep: 0:sleep allowed 1: sleep surpressed for special reason + // kindOfModem: 0:off 1: ATB_Sunlink_LTE (not yet implemented) + // kindOfCredit: 0:off 1: cVendTopp 2:cVendPin (not yet implemented) + + virtual void request_ReadbackDeviceSettings() const =0; + + virtual void readback_DeviceSettings(uint8_t *length, uint8_t *data) const =0; + // refer to DC2 manual for exact content + // state 5.5.21: byte[0]=kindOfPrinter byte[1]=kindOfCoinChecker + // byte[2]=kindOfMifarereadr byte[3]=suppress sleep mode + // byte[4]=kindOfModem byte[5]=kind of cc terminal + + virtual void sendMachineID(uint16_t customerNr, uint16_t machineNr, + uint16_t borough, uint16_t zone, + uint16_t alias, char *location) const =0; + + virtual void request_ReadbackMachineID() const =0; + + virtual void readback_machineIDdata(uint8_t *length, uint8_t *data) const =0; + // state 5.5.21: byte[0,1]=customer number byte[2,3]=machine number + // byte[4,5]=borough byte[6,7]=zone byte[8,9]=alias name + // byte[10...41]=location + + // Locks stops automatically at end switch or by timeout + virtual uint8_t lock_openUpperDoor(void) const =0; + virtual uint8_t lock_closeUpperDoor(void) const =0; + + virtual uint8_t lock_openLowerDoor(void) const =0; + virtual uint8_t lock_closeLowerDoor(void) const =0; + + virtual void shut_openOnce(void) const =0; + // and close automatic after shutter time + + virtual void shut_openForCoin(bool start) const =0; + // open flap if coin is attached + // once process is started it runs until stop command + + virtual void shut_sendOpeningTime(uint16_t timeIn_ms ) const =0; + // after this time without retrigger the flap is closed + + virtual void esc_takeMoney(void) const =0; + // and close automatically after escrow time (1s) + + virtual void esc_returnMoney(void) const =0; + // and close automatically after escrow time (1s) + + +// ---------------------------------------------------------------------------------------------------------- +// --------------------------------------------- MIFARE ----------------------------------------------------- +// ---------------------------------------------------------------------------------------------------------- + + + virtual uint8_t mif_returnReaderStateAndCardType(uint8_t *buf, uint8_t maxBufferSize) const =0; + // retval 0=OK 1=error host buffer too small + /* data description, new fast version: + byte 0= still the same: current read state: + 0=power off 1=reader-fault 2=ready + 3=just reading 4=read complete + 5=read partial, removed too early + 6=state unknown + + byte 1: reader state 1=ok 0=nok + byte 2: card preent (0,1) + byte 3: card selected (0) + byte 4: card type: 0...5 + byte 5: card allowed (0=no 1=MifareClassic 1k or 4k) + byte 6: CardSize: 1 or 4 (kB) + byte 7: length of UID 4 or 7 (byte) + */ + + virtual bool mif_readerIsOK(void) const =0; + + virtual bool mif_cardAttached(void) const =0; + + virtual uint8_t mif_readResult(void) const =0; + // result: 0: unknown or still in progress + // 1: card read successful + // 2: reading error + + virtual QString mif_cardUID(void) const =0; + + virtual uint8_t mif_getCardDataDec(uint8_t blkNr, uint8_t *buf, uint8_t maxBufferSize) const =0; + + virtual QString mif_getCardDataStr(uint8_t blockNumber) const =0; + // with blockNumber=0...11 + + + + // ---------------------------------------------------------------------------------------------------------- + // --------------------------------------------- PRINTER ---------------------------------------------------- + // ---------------------------------------------------------------------------------------------------------- + + // read printer condition and settings + + virtual uint8_t prn_getHwState(struct Tprn_hw_state *prn_hw_state) const =0; + // retval: status byte + // byte 0 = 0: prnter OK, >0: error + // bit0: paper low 1: no paper 2: temperature error + // 3: head open 4: paper jam in cutter + // 6: no response 7: bad response from printer + // and return struct "Tprn_hw_state" + + virtual bool prn_isUpAndReady(void) const =0; + // true: printer is powered, serial is ok, no error, printer is connected and resonding + + virtual void prn_getCurrentFontSetting(struct Tprn_currentSettings *prn_fonts) const =0; + + + // send Commands to printer: + + virtual void prn_sendText(QByteArray *buf) const =0; + // up to 1280 bytes + + virtual void prn_sendPrnSysCmd(uint8_t para1, uint8_t para2, uint32_t para3) const =0; + // send three byte through to printer, see printers manual + + virtual void prn_sendPrnEscCmd(uint8_t para1, uint8_t para2, uint8_t para3, uint8_t para4) const =0; + // send four byte through to printer, see printers manual + + + virtual void prn_sendPrnSetup(uint16_t paperSpeed, uint8_t density, uint8_t alignment, uint8_t orientation) const =0; + // send 5 byte: byte 0,1: speed 5...250 mm/s + // byte2: density 0....(25)....50 + // byte3: alignment 'l', 'c', 'r' = left, center, right + // byte4: orientation 0, 90, 180 = 0°, 90°, 180° rotation (by now not supported!) + // not batched! don't use twice within 100ms + + virtual void prn_movePaper(uint8_t wayInMm, uint8_t direction) const =0; + //direction: 1=forward 2=backward + // + virtual void prn_setFonts(uint8_t font, uint8_t size, uint8_t width, uint8_t height) const =0; + // font = kind of font 5...11 (0..22) + // size = 6...20, 9..9: too tiny 10: small ...12 = normal size ...20=huge + // width: 0...4 0=1x 1=2x 2=4x (huge!) 3=8x 4=16x (3,4 make no sense) + // heigth: 0...7 = 1x...8x only 0,1,2,(3) make sense + + virtual void prn_setLetters(uint8_t bold, uint8_t invers, uint8_t underlined) const =0; + // bold: 0/1 + // invers: 0/1 + // underlined: 0/1 + + virtual void prn_cut(uint8_t kindof) const =0; + // kindof: 1=full cut 2=partial cut 3=eject (5xLF + full cut) + + virtual void prn_newLine(uint8_t nrOfLines) const =0; + + virtual void prn_printCompleteFontTable(void) const =0; + + + virtual void prn_printBarcode(uint8_t kindOf, uint8_t withText, uint8_t offset, uint8_t rotation, uint8_t dataLeng, uint8_t *data) const =0; + // kind of barcode: 0=Code39 1=Code128 2=EAN13 3= 2/5interleaved 4=UPC-A 5=EAN8 + // withText: print readable text below + // offset: move by pixel from left border + // rotation + // dataLeng in byte + + virtual void prn_sendQRdata(QByteArray *buf) const =0; + // maximal 150 alphanummeric bytes + + virtual void prn_printQRcode(void) const =0; + // QRcode may have 1...150 alphanummeric data, must be transfered in advance + + + virtual void prn_printLogo(uint8_t nrOfLogo, uint8_t offset ) const =0; + // nrOfLogo: 1..4 in flash 5...8 in Ram + // offset: in mm form left border + + + // ......................................................... + // Parking Ticket (print-out document) designer TD - obsolete + // ......................................................... + + + + // ---------------------------------------------------------------------------------------------------------- + // --------------------------------------------- MDB Bus ---------------------------------------------------- + // ---------------------------------------------------------------------------------------------------------- + + virtual void mdb_sendBusReset(void) const =0; + + virtual void mdb_sendCommand(uint8_t toMdbDevice, uint8_t mdbCommand) const =0; + // send one bus command directly over mdb bus, refer to mdb manual for commands + // this command is not needed in normal operation, just for new or special things + + virtual void mdb_sendMessage(uint8_t toMdbDevice, uint8_t mdbCommand, uint8_t nrOfData, uint8_t *dataBuffer) const =0; + // nrOfData = sizeOf(dataBuffer) maximal 34 byte according mdb specs + // same as mdb_sendCommand, just with data + + virtual bool mdb_busIsReadyToWork() const =0; + + virtual bool mdb_deviceVoltageOK() const =0; + + virtual bool mdb_busVoltageOk() const =0; + + virtual uint8_t mdb_getLastDeviceResponse(uint8_t *fromDevice, uint8_t *lastRequest, + uint8_t *responseLength, uint8_t *responseBuffer) const =0; + // fromDevice: device nr from which data was requested 0,1,2,3 + // lastRequest: sent mdb command + // responseLength: nr of payload data (after mdb-ack) 0...34 + // responseBuffer holds payload data (answer from mdb device) + // return val: mdb result of this request: 1=got ACK 2=got 3xNAK 3=no or bad response 4:got Data (after ACK) + + + // ---------------------------------------------------------------------------------------------------------- + // ---------------------------------- Electronic Coin Validator EMP ----------------------------------------- + // ---------------------------------------------------------------------------------------------------------- + + + virtual void emp_sendSettings(uint16_t coinAcceptance, uint8_t tokenChannel, uint16_t *coinDenomination ) const =0; + // coinAcceptance: bit0=coin1 (lowest donomination) bit15=coin16 bitH=accept bit L = deny coin (no validation) + // tokenChannel 0...31: if this signal comes from emp then a token was inserted + // coinDenomination = array of 16 coin values (e.g. 5, 10, 20...) + + virtual void emp_pollingOnOff(uint8_t on) const =0; + + virtual void emp_startCoinAcceptance(void) const =0; + + virtual void emp_stopCoinAcceptance(void) const =0; + + virtual void emp_getAllParameters(struct T_emp *emp) const =0; + // see struct in hwapi.h + // usage example: + // hwapi *HWaccess const override; + // HWaccess = new hwapi() const override; + // struct T_emp myEmp const override; + // HWaccess->emp_getAllParameters(&myEmp) const override; + // readval=myEmp.pollingRunning const override; + + virtual uint8_t emp_chkIfCoinInserted(void) const =0; + // retval: 0...16 coins left in FIFO + + virtual void emp_getNewCoinRecord(uint8_t *valid, uint8_t *signal, uint8_t *error, uint16_t *value) const =0; + // with every call ONE coin is taken out of FIFO and pointer decremented + // valid: should be 1 + // signal: comes right from coin checker, 0...15 (0=first programmed coin type) 0xFF=no signal + // error: was reported from EMP as dynamic signal right after coin insertion (instead of + // coin signal), example: 3=unknown coin 4=coin is blocked by host. 0xFF=no error + // value: of the coin. Depends on parameter "coinDenomination" in function "emp_sendSettings" + // if coinDenomination[coin 0..15] = 0 then the value programmed in coin checker is taken + // if coinDenomination > 0 then this value is taken. + // Useful in case of two currencies (adapt to local currency) or for token. + + // function gives more details as "emp getLastCoin()" but "emp getLastCoin()" is easier to use + + // alternativ to emp_getNewCoinRecord( ): + virtual uint8_t emp_giveLastCoin(uint16_t *value, uint8_t *signal) const =0; + // retval: 0: NO coin stored 1: valid coin 2: got wrong coin or coin denied + // value: if retval1: value of the coin if reval=2: error number + // 0xFF means NO error or NO signal (as 0 is a valid error/signal) + // signal: channel nr reported from checker 0...15 + + + virtual uint8_t emp_returnLastCoin(uint16_t *value, uint8_t *signal) const =0; + // use for changer + + +#ifdef THIS_IS_CA_MASTER + virtual QString dc_getTxt4RsDiagWin(void) const =0; + virtual void dc_clrTxt4RsDiagWin(void) const =0; + virtual QString dc_get2ndTxt4RsDiagWin(void) const =0; + virtual void dc_clr2ndTxt4RsDiagWin(void) const =0; + virtual QString dc_getTxt4HsStateLine(void) const =0; + virtual void dc_clrTxt4HsStateLine(void) const =0; + virtual QString dc_getTxt4masterStateLine(void) const =0; + virtual void dc_clrTxt4masterStateLine(void) const =0; + virtual QString dc_getTxt4resultStateLine(void) const =0; + virtual void dc_clrTxt4resultStateLine(void) const =0; + virtual QString dc_getdataStateLine(void) const =0; + virtual void dc_clrTxt4dataStateLine(void) const =0; + virtual QString dc_getdatifLine(void) const =0; + virtual void dc_clrTxt4datifLine(void) const =0; +#endif + + + +// ---------------------------------------------------------------------------------------------------------- +// -------- DC Bootloader 1.Version +// ---------------------------------------------------------------------------------------------------------- + + // using DC2 Bootloader + virtual void bl_iniChain(void) const =0; + virtual bool bl_importBinFile(QByteArray readBinFile, uint32_t fileSize, char withDispl) const =0; + virtual uint8_t bl_activatBootloader(uint8_t *sendData) const =0; + virtual uint8_t bl_startChain(void) const =0; + virtual uint8_t bl_readBLversion(uint8_t *sendData) const =0; + // minimum size of sendData-buffer: 5byte retval: length + virtual uint8_t bl_readFWversion(uint8_t *sendData) const =0; + // minimum size of sendData-buffer: 5byte retval: length + + virtual uint8_t bl_prepareDC_BLcmd(uint8_t Cmd, uint8_t SendDataLength, uint8_t *sendData, uint8_t *outBuf) const =0; + // make BL protocol, retval = outbuf length (5...133) + // bring data in correct form: start always with 0x02 finish with 0x03 and append checksum + // 0x02 Cmd < ...sendData ..> CRC CRC 0x03 + // Data length = 0...64 + // special conversion: if data contain 2 or 3 (STX, ETX) then write two bytes: 0x1B (=ESC) and data|0x80 + // so maxlength = 5 + 2 x 64 (if all data are 2 or 3) without 2,3: maxlength = 5 + 64 + + virtual uint8_t bl_exitBL(uint8_t *sendData) const =0; + // minimum size of sendData-buffer: 5byte retval: length + + virtual void led_switchLedIllumination(uint8_t on) const =0; + + + + +// ------------------------------------------------------------------------------------ +// 27.3.2023: Use Device-Controller's Bootloader to send hex-file +// ------------------------------------------------------------------------------------ + + virtual void bl_rebootDC(void) const =0; + + virtual void bl_startBL(void) const =0; + virtual void bl_checkBL(void) const =0; + virtual bool bl_isUp(void) const =0; + // return true is bl is up and running + // also initializes "sendFile" + + virtual void bl_sendAddress(uint16_t blockNumber) const =0; + // send start address, nr of 64byte-block, start with 0 + // will be sent only for folling block-numbers: + // 0, 1024, 2048, 3072 and 4096, so basically every 64kByte + + virtual uint8_t bl_wasSendingAddOK(void) const =0; + // return val: 0: no response by now 1:error 10: OK + + virtual void bl_openBinary(void) const =0; + + virtual void bl_sendDataBlock(uint8_t length, uint8_t *buffer) const =0; + // send 64 byte from bin file + + virtual void bl_sendLastBlock(void) const =0; + + virtual uint8_t bl_wasSendingDataOK(void) const =0; + // return val: 0: no response by now 1:error 10: OK + + virtual void bl_stopBL(void) const =0; + + +// ------------------------------------------------------------------------------------ +// 6.4.2023: new functions for coin collection and printing +// some new system functions +// ------------------------------------------------------------------------------------ + + + virtual bool rtc_setTimeDateDirect(struct Trtc_DateTime *DateTime) const =0; + // return true if successful. could fail if more the 8 commands are waiting + + virtual bool rtc_getExtendedTime(uint8_t *leng, uint8_t *data) const =0; + + virtual bool rtc_getExtendedTime(struct T_extTime *exTime) const =0; + + virtual bool sys_runCompleteTest(void) const =0; + // warning: lasts 20s in one pace + + virtual bool sys_ready4sending(void) const =0; + // return true if a Json-file can be sent + + virtual bool sys_sendJsonFileToDc(uint8_t kindOfFile, uint8_t nrOfTemplate, uint8_t *content ) const =0; + // kindOfFile: 1=config, 2=device, 3=cash, 4=serial, 5=time, 6=printer + // nrOfTemplate=1...32 if kindOfFile==6 + // content = content of the Json file, max 800byte ascii signs + // file is 0-terminated! + // return false if sending is not possible, wait a second + + virtual bool prn_sendDynamicPrnValues(uint8_t *dynPrnVal ) const =0; + // dynPrnVal = array of 8 Variables with 8 byte each, come as ascii string + // like: char prn_dynPrnVal[8][8]; + // return true if sending, false if cmd-stack is full + + virtual bool prn_printTemplate(uint8_t nrOftemplate) const =0; + // print one of the templates loaded by Json prior + // nr = 1..32 + // return true if sending, false if cmd-stack is full + + virtual void log_getHoldAccountNumbers(uint8_t *nrOfVals, uint16_t *accNr ) const =0; + // returns all acc nrs of the backuped vault records + // use: uint16_t backupedAccNumbers[8] + + virtual bool log_selectVaultRecord(uint16_t accountNr ) const =0; + // return true if sending, false if cmd-stack is full + // and trigger transfer + + virtual bool log_chkIfVaultRecordAvailable(void) const =0; + // return true if completly received + + virtual bool log_getVaultRecord(struct T_vaultRecord *retVR) const =0; + // which was selected by: log_selectVaultRecord() + // to be forwarded to Ismas + + virtual bool prn_printAccountReceipt(void) const =0; + // return true if sending to DC OK, false if cmd-stack is full + + virtual bool prn_printTestTicket(void) const =0; + // return true if sending to DC OK, false if cmd-stack is full + + + + + virtual bool cash_startPayment(uint32_t amount) const =0; + // 17.4.23TS: extended to 32bit + + virtual uint8_t cash_paymentProcessing(void) const =0; + // run this function periodically while coin payment process to generate necessary signals + // return value: + // 0: stopped 1: starting up 2: coin collection + // 3: finished by User (Push button) 4: finished, Max-Value collected + // 5: finished by escrow + // 10,11: error cannot start + // 12: timeout while payment, coins returned + // 13: stopped by unexpected error + + virtual uint32_t getInsertedAmount(void) const =0; + + virtual uint16_t getLastInsertedCoin(void) const =0; + + virtual bool getAllInsertedCoins(uint16_t *types, uint16_t *values) const =0; + // alle bei diesem Verkauf eingeworfenen Münzen sind gespeichert, max 64 + + + virtual bool cash_cancelPayment(void) const =0; + // and return coins + + virtual bool cash_stopPayment(void) const =0; + // and keep coins in escrow + + + // after ticket/goods issue: + virtual bool vend_success(void) const =0; + // conclude payment process, encash all inserted coins to vault. Printing was successful + // if possible return change + + virtual bool vend_failed(void) const =0; + // conclude payment process and return all inserted coins + + + + + + virtual uint8_t mif_getCardType(QString *cardholder) const =0; + // return 1,2,3,4 = upper, lower access card, printer test, coin test + // cardholder: 7byte Name-String + + virtual uint64_t sys_getWakeSource(void) const =0; + // retval: 6 bytes, bit coded, 1=event keeps DC awake + + virtual uint8_t sys_getWakeReason(void) const =0; + // Master was woken by following reason: + // 1: MDB Event + // 2: Coin Event + // ( 3: Master Event) - will not set the wake line + // ( 4: 32s pulse) - will not set the wake line + // 5: Door Event + // ( 6: Diag Event) - will not set the wake line + // 7: 30min-Pulse for HB + + virtual void sys_getDeviceConditions(uint8_t *leng, uint8_t *data) const =0; + + virtual void sys_getDeviceConditions(struct T_moduleCondition *devCond) const =0; + + virtual void sys_getDynMachineConditions(uint8_t *leng, uint8_t *data) const =0; + + virtual void sys_getDynMachineConditions(struct T_dynamicCondition *dynMachCond) const =0; + + + virtual uint32_t cash_getAmountInVault(void) const =0; + + virtual uint16_t cash_getNrCoinsInVault(void) const =0; + + virtual uint8_t prn_getPrintResult() const =0; + + virtual uint8_t prn_getCurrentPrinterState() const =0; + // 0: printer OK + // bit0: near paper end bit1: no paper + // bit2: temperature error bit3: error head open + // bit4: paper jam in cutter + // bit6: no response bit7: serial rec. error + // bit5: printer not ready + + + virtual void sys_sendDeviceParameter(struct T_devices *deviceSettings) const =0; + + virtual void sys_restoreDeviceParameter(struct T_devices *deviceSettings) const =0; + + virtual bool sys_areDCdataValid(void) const =0; + + virtual bool sys_sendingTest(void) const =0; + + virtual void prn_requestCurrentDynData(void) const =0; + + virtual bool prn_getCurrentDynamicPrnValuesFromDC(uint8_t *dynPrnVal ) const =0; + // which was sent with: bool prn_sendDynamicPrnValues(uint8_t *dynPrnVal ) const =0; + + virtual bool prn_dynDataAreEqual(uint8_t *buf) const =0; + + virtual bool prn_printKombiticket(uint8_t nrOfKombi) const =0; + // print four of the templates loaded by Json prior + // nr = 1..8 + + virtual void lock_triggerUpperSolenoid(void) const =0; + + virtual void lock_triggerLowerSolenoid(void) const =0; + + virtual bool doors_supervise(void) const =0; + + virtual bool dc_isAutoRequestOn(void) const =0; + + + + +signals: + virtual void hwapi_templatePrintFinished_OK(void) const=0; + virtual void hwapi_templatePrintFinished_Err(void) const=0; + + virtual void hwapi_coinCollectionJustStarted(void) const=0; + virtual void hwapi_coinCollectionAborted(void) const=0; + + virtual void hwapi_gotNewCoin(void) const=0; + virtual void hwapi_payStopByMax(void) const=0; + virtual void hwapi_payStopByPushbutton(void) const=0; + + virtual void hwapi_payStopByEscrow(void) const=0; + virtual void hwapi_payStopByError(void) const=0; + virtual void hwapi_payStopByTimeout(void) const=0; + virtual void hwapi_payCancelled(void) const=0; + virtual void hwapi_coinProcessJustStopped(void) const=0; + + + // new from 2023.06.12 + virtual void hwapi_doorServiceDoorOpened(void) const=0; + virtual void hwapi_doorVaultDoorOpened(void) const=0; + virtual void hwapi_doorCoinBoxRemoved(void) const=0; + virtual void hwapi_doorCoinBoxInserted(void) const=0; + virtual void hwapi_doorCBinAndAllDoorsClosed(void) const=0; + virtual void hwapi_doorAllDoorsClosed(void) const=0; + + + +}; + + +// History +// 11.10.2021: V1.0 222 functions +// 23.12.2021: V1.1 added block-parameter to function "read mifare data" +// 30.12.2021: V1.2 added function: mif_clearDataBuffer(), mif_isBlockAvailable(uint8_t blkNr) and mif_getAvailableDataBlocks() +// 1.1.2022: V1.3 Mifare extended. ( background: read 16 x 48byte from card to DC, read 12 x 64byte from DC to CA) +// new: read full card with 768bytes from HWapi without block borders +// added: mif_getNrOfAvailableDataBytes mif_getCardData768byteDec(uint8_t *buf, uint16_t bufferSize) +// mif_getCardDataDec(uint16_t fromAddr, uint16_t toAddr, uint8_t *buf, uint16_t bufferSize) +// mif_getCardDataStr(bool useHexFormat, char seperator) + +// 29.03.2023: V3.1 some extensions for PSA1256_ptu5, +// V3.2 Bootloader improvement +// 12.04.2023: V3.3 new features extended: loading and using Json-files, cash-collection, cash-data-logging +// 14.04.2023: V3.4 new features extended: sys_getDynMachineConditions, sys_getDeviceConditions and +// rtc_getExtendedTime return struct in addition. New function to select and get VaultRecord +// +// 19.04.2023: V3.5 new function: sys_getWakeReason(); +// 17.05.2023: V3.6 new function: cash_isCollectionActive(), cash_isPayProcessActive() +// new signals: hwapi_coinCollectionJustStopped, hwapi_coinCollectionJustStarted +// getAllInsertedCoins() fixed, also in datif and storeINdata + +// 15.06.2023 V4.2 bring into same order as hwapi in order to set the THIS_IS_CA_MASTER correct +// 19.06.2023 V4.3 added some qCriticals to see emits + + +//#define HWINF_iid "Atb.Psa2020.software.HWapi/3.1" +//#define HWINF_iid "Atb.Psa1256ptu5.software.HWapi/3.1" +//#define HWINF_iid "Atb.Psa1256ptu5.software.HWapi/3.3" +//#define HWINF_iid "Atb.Psa1256ptu5.software.HWapi/3.4" +//#define HWINF_iid "Atb.Psa1256ptu5.software.HWapi/3.5" +//#define HWINF_iid "Atb.Psa1256ptu5.software.HWapi/3.6" +//#define HWINF_iid "Atb.Psa1256ptu5.software.HWapi/4.0" +//#define HWINF_iid "Atb.Psa1256ptu5.software.HWapi/4.1" +//#define HWINF_iid "Atb.Psa1256ptu5.software.HWapi/4.2" +#define HWINF_iid "Atb.Psa1256ptu5.software.HWapi/4.3" + + + + +Q_DECLARE_INTERFACE(hwinf, HWINF_iid) + + +#endif + + +